我手上3台阅星曈,2台X4、1台X3,系统版本全是阅星曈官方系统V6.0.15,全成了砖头。
你现在去看一下自己设备的系统版本,如果也是V6.0.15,那咱们情况一样。
这版系统没法OTA升级,没法回退到上一版V5.6.33,也没法升到阅星曈发布的最新版V6.2.4。
阅星曈发了一个公告:深表歉意。
所以,目前成砖的设备,要么停在这个版本凑合用一辈子,要么刷机。
没有第三条路。
今天这篇,就拿我手上这3台砖头做演示,把线刷和卡刷的完整流程走一遍。
个别术语看不懂的,看我以前写的这篇文章,今天就不再重复了:PaperS3实测:一块开发板是怎么干翻一堆阅读器的(附刷机教程)
⚠️风险提示与免责声明:刷机有风险,本文只提供方法,不替商家承担任何因刷机造成的设备损坏、数据丢失等意外。有问题先找阅星曈客服。同意再往下看。
目前解决砖头系统一共4条路径:1
京东买的,别忘了你有"180天只换不修"的权益。 新机送上门,旧机回收,最省事。
2
返厂寄回阅星曈刷机。返厂有可能拆机,提前和客服沟通好,拆机后不保修,留好凭证证明不是自己拆的。邮费由阅星曈承担,来回至少7天。(拆过机的卖二手会掉价)
3
无锁机线刷。最简单。
4
有锁机卡刷。操作不难,但繁琐,得挨个试。
我建议优先用方法1和2,没金钱损失,也没啥大的时间损失。
方法3和4对普通用户不友好。你买的是墨水屏阅读器,不是买来一台设备小心翼翼的伺候着,把自己变成调试专家。
他们内部怎么评估这起OTA把用户设备变砖的事故,先不讨论了。
先把设备救回来,这才是现在最要紧的事。
得亏阅星曈的固件更新还要手动联网操作。要是像Kindle那样联网自动推送,那就是灾难性事故了。
刷机前的准备
提前备份数据,线刷、卡刷都可能清空数据。
充电到50%以上,别升级到一半没电。
怎么判断自己设备有锁还是无锁
2个办法。
第一,用数据线把X3/X4连到电脑,电脑有提示,设备管理器里能看到端口号,就是无锁机。
第二,进X3/X4的设置,拉到最后一项,最后一项是"清理缓存"就是无锁,最后一项是"SN X......"一长串数字就是有锁。
线刷仅限无锁机。
最早几批在小程序购买、以及其它平台早期的机子是无锁的,后来阅星曈为了封堵第三方刷机固件,出厂的机器改成了有锁。
如果不识别端口,线刷是没可能的。
无锁机:线刷
谷歌浏览器打开:https://www.xteink.cn/app/firmware-flash
别问为啥用谷歌,因为待会要弹出端口连接提示,谷歌最稳。
用数据线把X3/X4连接电脑。
此电脑——右键——管理——设备管理器——端口,能看到端口号就说明识别成功。
提示无法识别就换线,一定要用数据线,不是那种只能充电的线。
然后看截图,一共5个步骤。
选"不同固件全量刷写",选型号,X3就选X3,X4就选X4,别选错。步骤4勾选,然后"确认并开始全量刷写"。
谷歌浏览器会弹出"www.xteink.cn 想连接到串行端口",点连接。
等进度条到100%,期间不要跳开页面。
提示刷机成功后,先按复位键,再按开机键。
注意注意,不同固件全量刷写,写进去的固件版本不一定是最新的。
我的X4被写入的是V5.2.13的系统,然后我连接WiFi,再点系统升级,就可以在线OTA升级了。
再去看系统版本,V6.2.4,搞定。
线刷很简单,你别看步骤写得多,那是为了让新手看懂,实际上点几下就行。
有锁机:卡刷
有锁机不识别端口,只能把设备里的SD卡掏出来,插到读卡器上接电脑,把固件拷贝到SD卡根目录,再插回设备启动引导刷入系统。
卡刷之前两个关键点,十分重要。
第一,搞明白根目录——点开SD卡就是根目录,不要再点里面的文件夹。
第二,固件放到根目录后插回设备,靠同时按住"电源键+上键"启动系统引导。注意注意:V6.0.15默认的上下键是反的,或者你自己改过上下键的,先改回来。
(下图红框标的这个才是正确的,也必须有且仅能是这种设置)
卡刷原理是先刷第三方固件覆盖V6.0.15这个砖头系统,再回退到V5.6.33或者直接升到V6.2.4。
打开 https://crossmux.yunhug.com/ ,右上角"下载固件",根据设备选固件,带中文的几个都能用。
下载后复制到SD卡根目录,重命名为update.bin,这步必须做。
电脑上弹出SD卡,插回设备,同时按住"电源键+上键"。
设备显示更新中,成功就会进入新系统。
如果报错或者直接又进入老系统了,说明失败了,换别的版本的中文固件再试。
这种第三方固件卡刷方式不是所有机子都能成功。
8月3号之前有人靠这方法成功了,但我手上的2台有锁机,一台X3一台X4,都失败了。
如果到这一步还没搞定,中药不管用了,得上西药。
打开 https://crosspointreader.com/unlocker
在电脑上安装Xteink Unlocker。
原理是利用电脑网卡临时建一个热点,骗过阅星曈有锁机的封堵,让设备进入"闪存应急解锁固件"。
事先先把固件拷贝到SD卡,把SD卡插入到机器里面,并重命名update.bin。
这个软件很傻瓜,你一步一步跟着我截图走。
选对设备,你国内就选Chinese。
注意注意,最核心、最关键的一步来了,点这个绿色的“Flash Escape Hatch firmware”。
这一步他已经临时建立了一个名为crosspoint 的临时WiFi,密码是八个1。
然后你掏出你的设备,找到这个WiFi,并连接。这是绕开阅星曈锁固件的关键一步。
crosspoint的WiFi连接成功之后,就去点一下系统升级,这时候访问的就不是阅星曈的服务器了。
点击更新,就会进入一个微型系统。
在这个微型系统里面,找到我们重命名的update.bin这个文件。
按键按对钩。
弹出的提示里面,再按对钩。
等进度条走完。
最后看下刷完机的版本号,V5.6.33,是我拷贝进去的版本,说明刷机成功。
我测试的时候给X4刷了V6.2.4,给X3刷了V5.6.33,都成功了。
注意注意,刷成功之后,电脑上Xteink Unlocker,点一下Clean UP,把热点释放掉。
目前还有一个隐患:不管线刷还是卡刷,系统是写进去了,但往后OTA升级能不能顺利进行,还得观察。
对了,阅星曈对此次事件的补偿是一台设备500积分,积分我收到了,3台设备总共收到1500积分。
哎......
再次提示,刷机前看下我文章开头的风险提示与免责声明,风险自担。任何疑问,都是先去联系阅星曈的客服。
I have three Xteink devices on hand: two X4s and one X3, all with the official Xteink system version V6.0.15, and they've all become bricked.
Now check your own device's system version. If it's also V6.0.15, then our situations are the same.
This system version cannot OTA upgrade, cannot revert to the previous version V5.6.33, and cannot upgrade to the latest version V6.2.4 released by Xteink.
Xteink issued an announcement: We deeply apologize.
So, for devices that are currently bricked, either stick with this version and make do for life, or flash the firmware.
There is no third option.
In this article today, I'll use these three bricked devices on hand to demonstrate, walking through the complete process of both USB flashing and SD card flashing.
For any terminology you don't understand, see this previous article I wrote: PaperS3 Review: How a Development Board Took Down a Bunch of Readers (with Flashing Tutorial).
⚠️Risk Warning and Disclaimer: Flashing carries risks. This article only provides methods; I am not responsible for any equipment damage, data loss, or other incidents caused by flashing. If you have issues, contact Xteink customer service first. Proceed only if you agree.
Currently, there are four paths to resolve bricked systems: 1
If bought from JD.com, don't forget you have the "180-day replacement-only" benefit. A new machine delivered, old one recycled – the easiest option.
2
Return to factory for Xteink to flash. Return may involve disassembly, so communicate with customer service in advance; after disassembly, warranty is void, keep proof that you didn't disassemble it. Shipping costs are borne by Xteink, round trip at least 7 days. (Disassembled units will lose value when sold second-hand.)
3
USB flash for unlocked devices. The simplest.
4
SD card flash for locked devices. Not difficult, but tedious, must try one by one.
I recommend prioritizing methods 1 and 2; no financial loss and minimal time loss.
Methods 3 and 4 are not user-friendly for ordinary users. You bought an e-ink reader, not a device to be coddled; don't turn yourself into a debugging expert.
How they internally assess this OTA incident that bricked user devices is not discussed now.
First, get the devices back; that's the most urgent matter now.
Fortunately, Xteink's firmware updates require manual network connection. If it were automatic like Kindle, it would be a disastrous accident.
Preparation before flashing
Back up data in advance; USB flashing and SD card flashing may clear data.
Charge to over 50% to avoid running out of power during upgrade.
How to determine if your device is locked or unlocked
Two methods.
First, connect X3/X4 to computer via data cable; if computer prompts and you can see port number in Device Manager, it's unlocked.
Second, go into X3/X4 settings, scroll to the last item. If last item is "Clear Cache", it's unlocked; if last item is "SN X......" a long string of digits, it's locked.
USB flashing is only for unlocked devices.
Early batches purchased via mini-program and other platforms' early units were unlocked; later, Xteink changed factory settings to locked to block third-party flashing firmware.
If port is not recognized, USB flashing is impossible.
Unlocked device: USB flashing
Open in Google Chrome: https://www.xteink.cn/app/firmware-flash
Don't ask why Google; because a port connection prompt will appear later, and Google is most stable.
Connect X3/X4 to computer with data cable.
This PC – right-click – Manage – Device Manager – Ports; seeing port number means recognition successful.
If prompted unrecognizable, change cable; must use data cable, not just charging cable.
Then refer to screenshots; total of five steps.
Select "Different firmware full flash", choose model, X3 select X3, X4 select X4, don't choose wrong. Check step 4, then "Confirm and start full flash".
Google Chrome will pop up "www.xteink.cn wants to connect to serial port"; click connect.
Wait for progress bar to 100%; do not switch away from page during this time.
After flashing success prompt, first press reset button, then press power button.
Note note, different firmware full flash, the flashed firmware version is not necessarily the latest.
My X4 was flashed with V5.2.13 system; then I connected WiFi, and clicked system update, so I could OTA upgrade online.
Then check system version; V6.2.4, done.
USB flashing is simple; don't let the many steps scare you, they're for beginners; actually just click a few times.
Locked device: SD card flashing
Locked devices don't recognize port; only way is to take out SD card from device, insert into card reader connected to computer, copy firmware to SD card root directory, then insert back into device to boot guide and flash system.
Two key points before SD card flashing, very important.
First, understand root directory – opening SD card is root directory; don't click into folders inside.
Second, after placing firmware in root directory and inserting back into device, rely on simultaneously pressing "power button + up button" to start system guide. Note note: V6.0.15 default up/down buttons are reversed, or if you changed them, change back first.
(The red box in the image below marks the correct one, and must be this setting only.)
Principle of SD card flash is first flash third-party firmware to overwrite the bricked V6.0.15 system, then revert to V5.6.33 or directly upgrade to V6.2.4.
Open https://crossmux.yunhug.com/, top right "Download Firmware", select firmware according to device; those with Chinese can be used.
After downloading, copy to SD card root directory, rename to update.bin; this step is mandatory.
Eject SD card from computer, insert back into device, simultaneously press "power button + up button".
Device shows updating; successful will enter new system.
If error or directly back to old system, means failed; try other version of Chinese firmware.
This third-party firmware card flash method does not succeed for all devices.
Before August 3rd, someone succeeded with this method, but my two locked devices, one X3 and one X4, both failed.
If still not resolved at this point, Chinese medicine no longer works; must use Western medicine.
Open https://crosspointreader.com/unlocker
Install Xteink Unlocker on computer.
Principle is using computer network card to temporarily create a hotspot, trick Xteink locked device block, let device enter "flash emergency unlock firmware".
First copy firmware to SD card, insert SD card into machine, and rename update.bin.
This software is very foolproof; follow my screenshots step by step.
Select correct device; for domestic, choose Chinese.
Note note, most core, most critical step is here; click this green "Flash Escape Hatch firmware".
At this step, it has temporarily created a WiFi named crosspoint, password is eight 1s.
Then take out your device, find this WiFi, and connect. This is the key step to bypass Xteink lock firmware.
After crosspoint WiFi connection successful, go click system update; at this time, accessing is not Xteink server.
Click update, will enter a micro system.
In this micro system, find the file update.bin we renamed.
Press button with check mark.
In pop-up prompt, press check mark again.
Wait for progress bar to finish.
Finally check flashed version number; V5.6.33, which is the version I copied in, means flashing successful.
During testing, I flashed X4 with V6.2.4, X3 with V5.6.33, both successful.
Note note, after flashing successful, on computer Xteink Unlocker, click Clean UP, release the hotspot.
Currently still one hidden risk: whether USB flash or card flash, system is written, but whether OTA upgrade can proceed smoothly later, still to be observed.
By the way, Xteink's compensation for this incident is 500 points per device; I received points, for three devices total 1500 points.
Sigh...
Reminder again, before flashing check the risk warning and disclaimer at the beginning of my article; risk borne by self. Any questions, first contact Xteink customer service.