IT之家 9 月 24 日消息,特斯拉过去几个月一直很少公开谈及人形机器人项目,但其自家的手机 App 可能无意间泄露了相关信息。有人在特斯拉 App 深处发现了一批新的数字资产,似乎曝光了未经遮挡的量产版 Optimus Gen 3 人形机器人。
特斯拉爱好者 @WholeMars 在近期更新的特斯拉 Android App 中找到了这些渲染模型。虽然原帖后来被删除,但在删除之前,相关内容已经被 @TeslaNewswire 转发。与风格化的概念草图不同,这些文件是特斯拉官方内置于 App 中的 UI 模型,用于在手机端展示特斯拉机器人。
此次提取出的渲染模型给出了即将推出的 Gen 3 与此前 Gen 2.5 原型机的直接比较,可以显著看出特斯拉正在进一步朝大规模量产方向推进。
Optimus Gen 2.5 的小腿部分使用外露式机械连杆,并配有金色金属饰板;相比之下,Gen 3 的总体外观显著更加简洁,也更具工业机型气质。
首先,Gen 3 的骨盆和髋部组件开展了重新外观。在躯干与大腿上部的连接处加入了一体式柔性关节护罩,可以将容易夹伤的部位以及轴承等机械结构遮挡起来,减少外部灰尘和碎屑进入,同时也让总体外观更加整洁、精致。
其次,Gen 2.5 膝盖和小腿护板上的亮金色饰面被低调的哑光黑色外壳取代,与香槟金色部件搭配后,形成更加统一的黑色与香槟金双色外观。
机器人的手臂和手部看起来也更加完整,其中 Gen 3 的双手尤其开展了大幅升级。据特斯拉介绍,Optimus Gen 3 的双手具备 22 个自由度,能力已经接近人类的手部能力。
另外,Gen 3 的总体外部面板贴合得更加紧密,进一步简化了机器人的轮廓,使其看起来更像一款面向消费者的成熟硬件机型,而不是机械结构大量裸露的实验室测试设备。
Gen 3 一直被定位为专门针对工厂大规模生产而外观的版本。从此次曝光的精细化外观来看,制造工艺的简化以及最终机型的外观都被放在了格外关键的位置。
特斯拉此前曾推迟 Optimus Gen 3 的公开亮相,埃隆 · 马斯克(Elon Musk)今年春季早些时候曾表示,这款机器人在正式登台前还需要开展一些“收尾工作”。
IT之家注意到,外界最近一次看到特斯拉官方展示 Gen 3,是今年早些时候的一场工程工艺演示。当时,特斯拉 Optimus 项目负责人展示了一张 Gen 3 的机器人轮廓图。
当下,特斯拉正将重心放在即将于 10 月 1 日在得克萨斯州韦科举行的下一代 Roadster 发布活动上,因而 Optimus 如果单独举行发布或展示活动,更有可能是在今年晚些时候或明年年初。
在幕后,Optimus 的生产准备工作已经快速推进。今年夏初,特斯拉开始改造位于弗里蒙特工厂、此前用于生产 Model S 和 Model X 的生产线,用于组装 Optimus,目标是在产能爬坡后达到年产 100 万台。
将来的产能目标还要高得多。特斯拉计划在后续将得州超级工厂(Gigafactory Texas)的 Optimus 年产能提高至 1000 万台。特斯拉原本计划在今年启动 Optimus 的大规模量产,而当下距离年底还有大约 3 个月时间,因而这一计划仍有可能达成。
此次在特斯拉 App 内发现这些 3D 模型,也进一步表明特斯拉已经在为软件层面的兼容做准备,将来车主和机器人车队管理人员可能可以直接借助手机监控自己的机器人。
现在,剩下的似乎只是等待特斯拉正式公开发布 Optimus。
本文来源:https://www.ithome.com/1/006/793.htm
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。
Thanks to IT之家 netizens 软媒使用者1238620, 不一样的感受, and 华南吴彦祖 for their tip submissions!
IT之家 news on September 24: Tesla has rarely spoken publicly about its humanoid robot project over the past few months, but its own mobile app may have inadvertently leaked relevant information. Someone has discovered a new batch of digital assets deep within the Tesla app, which appear to reveal the unshielded mass-produced version of the Optimus Gen 3 humanoid robot.
Tesla enthusiast @WholeMars found these render models in a recently updated Tesla Android app. Although the original post was later deleted, the relevant content had already been reposted by @TeslaNewswire before deletion. Unlike stylized concept sketches, these files are official UI models built into the Tesla app, used to display the Tesla robot on mobile devices.
The extracted render models provide a direct comparison between the upcoming Gen 3 and the previous Gen 2.5 prototype, clearly showing that Tesla is further advancing toward large-scale mass production.
The lower legs of the Optimus Gen 2.5 use exposed mechanical linkages paired with gold metal trim panels. In contrast, the overall appearance of the Gen 3 is significantly cleaner and carries more of an industrial machine aesthetic.
First, the Gen 3's pelvis and hip components have been redesigned. An integrated flexible joint cover has been added at the connection between the torso and the upper thighs, which shields areas prone to pinching as well as mechanical structures such as bearings, reducing the entry of external dust and debris while also making the overall appearance neater and more refined.
Second, the bright gold finish on the Gen 2.5's knee and lower-leg covers has been replaced with a subdued matte black shell, which, when paired with the champagne gold components, creates a more unified black-and-champagne-gold two-tone appearance.
The robot's arms and hands also look more complete, with the Gen 3's hands in particular receiving a major upgrade. According to Tesla, the Optimus Gen 3's hands have 22 degrees of freedom, with capabilities approaching those of human hands.
Additionally, the Gen 3's overall exterior panels fit more tightly together, further simplifying the robot's silhouette and making it look more like a mature consumer-grade hardware product rather than a laboratory test device with extensively exposed mechanical components.
The Gen 3 has always been positioned as the version specifically designed for large-scale factory production. Judging by the refined appearance revealed this time, both the simplification of manufacturing processes and the final product's appearance have been placed at a particularly critical level of importance.
Tesla had previously delayed the public unveiling of the Optimus Gen 3. Elon Musk stated earlier this spring that the robot still needed some "finishing work" before it could officially take the stage.
IT之家 notes that the most recent time the public saw Tesla officially showcase the Gen 3 was during an engineering process demonstration earlier this year. At that time, the head of Tesla's Optimus project displayed a silhouette image of the Gen 3 robot.
Currently, Tesla is focusing its attention on the next-generation Roadster launch event scheduled for October 1 in Waco, Texas. As a result, if Optimus were to hold a separate launch or showcase event, it would more likely take place later this year or early next year.
Behind the scenes, production preparation for Optimus has been advancing rapidly. In early summer, Tesla began retrofitting the production line at the Fremont factory that previously manufactured the Model S and Model X for assembling Optimus, with a target of reaching an annual production capacity of 1 million units after production ramps up.
Future production targets are much higher. Tesla plans to subsequently increase Optimus annual production capacity at Gigafactory Texas to 10 million units. Tesla originally planned to start mass production of Optimus this year, and with roughly three months remaining until the end of the year, this plan could still be achievable.
The discovery of these 3D models within the Tesla app further indicates that Tesla is already preparing for software-level compatibility, and in the future, owners and robot fleet managers may be able to monitor their robots directly through their mobile phones.
For now, it seems all that remains is to wait for Tesla to officially unveil the Optimus to the public.

