800 美元交换机 PoE++ 失效?两颗浪涌保护器件“自我牺牲”酿成的故障$800 Switch PoE++ Failure? Fault Caused by Two Surge Protection Devices' "Self-Sacrifice


AI free token/AI免费积分
800 美元交换机 PoE++ 失效?两颗浪涌保护器件“自我牺牲”酿成的故障

The Parallel Port 频道最近接到一台交换机维修委托:一台 Ubiquiti USW-Pro-Max-24-PoE 24 口机架式交换机,配备 2.5G RJ-45 端口和两个 10G SFP+ 端口,本身一切正常,唯独 400W 的 PoE++ 供电功能完全失效——对于一台 800 美元购入的新设备来说,这显然让人恼火。

上电后交换机正常启动,包括那块 1.3 英寸触控屏。登录 BusyBox 控制台后可以看到所有端口的 PwrGood 状态均为 bad,日志中还有 PoE 电源状态请求错误。用 PoE 分离器实测,PoE 功能确实已经死亡。

拆机后用万用表和热成像仪排查,发现短路点位于 PoE 电源板连接的 PCB 区域,且把该板拆下后短路依旧。考虑到设备经历过一次电气事故,先检查了 TVS 二极管——完好无损。但它旁边的两颗标注为保险丝的 Trisil 晶闸管浪涌保护器件(作为撬棒式保护使用)实测均已对地短路。显然,它们在电气事件中承受了主要冲击并"自我牺牲",导致 PoE 供电通路被锁死。

更换这两颗器件后,交换机的 PoE 状态恢复正常,甚至能通过 PoE 分离器点亮一个直流风扇。故障本身并不复杂,但也证明了读懂保护电路的工作原理,能让这类故障的诊断与维修少走大量弯路。

本文来源:https://hackaday.com/2026/09/25/reviving-the-poe-feature-on-a-ubiquiti-switch/
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。

The Parallel Port channel recently received a switch repair commission: a Ubiquiti USW-Pro-Max-24-PoE 24-port rack-mounted switch, equipped with 2.5G RJ-45 ports and two 10G SFP+ ports, everything itself normal, except the 400W PoE++ power supply function completely failed—for a new device purchased at $800, this is obviously frustrating.

After powering on, the switch started normally, including the 1.3-inch touch screen. After logging into the BusyBox console, all ports' PwrGood status were bad, and the logs also had PoE power status request errors. Using a PoE splitter for actual testing, the PoE function was indeed dead.

After disassembly, using a multimeter and thermal imaging camera for troubleshooting, it was found that the short circuit was located in the PCB area connected to the PoE power board, and after removing that board, the short circuit remained. Considering the device had experienced an electrical accident, first checked the TVS diode—intact. But the two Trisil thyristor surge protection devices next to it, labeled as fuses (used as crowbar protection), were both measured short-circuited to ground. Obviously, they absorbed the main impact during the electrical event and "sacrificed themselves", causing the PoE power supply path to be locked.

After replacing these two devices, the switch's PoE status returned to normal, and it could even light up a DC fan through a PoE splitter. The fault itself was not complicated, but it also proved that understanding the working principle of the protection circuit can save a lot of detours in diagnosing and repairing such faults.

$800 Switch PoE++ Failure? Fault Caused by Two Surge Protection Devices'

暂无评论,快来发表第一条评论吧!No comments yet. Be the first!

📮 需求咨询📮 Inquiry