FPGA 编年史:详解低价开源友好的 Tang Nano 20K(GOWIN GW2AR-18)FPGA Chronicle: A Detailed Look at the Low-Cost, Open-Source-Friendly Tang Nano 20K (GOWIN GW2AR-18)


AI free token/AI免费积分
FPGA 编年史:详解低价开源友好的 Tang Nano 20K(GOWIN GW2AR-18)

Hackaday 连载《FPGA 编年史》开篇,作者 Al Williams 宣布重启早年的 FPGA Bootcamp 教程,改用以 GOWIN GW2AR-18 为核心的入门板 Tang Nano 20K 作为主平台。

文章先回顾了 FPGA 的历史:从「一车钱」定制的掩膜与编程 ASIC,到把未连接的功能块做成可配置互联,最终让普通人也能自定定制芯片。为什么要用 FPGA?课堂上的红绿灯只是演示状态机;真正的价值场景例如火箭上数百个数字传感器要求任一信号在几微秒内报警——处理器必须分组采样、处理中断,而 FPGA 可以直接实现一个巨大的或门,持续监视所有输入且不被其他逻辑抢占时间。

硬件方面,GW2AR-LV18QN88C8/I7 内含 20736 个四输入查找表(LUT4)与 15552 个触发器;在合理流水线设计下可稳定运行在低百兆赫兹。芯片最出色之处是存储:同时具备分布式 RAM 与块 RAM,并封装了独立的 8MB 32-bit SDR SDRAM。板卡还配有 48 个 18×18 乘法器、可编程时钟发生器、64Mbit QSPI Flash,以及音频、LCD、microSD 与 HDMI 接口;板载 MCU 可用于烧写时钟发生器、JTAG 下载及提供虚拟串口。

教程接着演示完整流程:用 Verilog 定义逻辑、建立顶层模块、写引脚约束(IO_LOC / IO_PORT)、综合、布局布线生成 bitstream、下载到 RAM 或配置 Flash。作者还给出 GOWIN IDE 在 Linux 下的踩坑记录(libfreetype 冲突、LD_LIBRARY_PATH 设置),以及通过 /etc/udev/rules.d/99-tang-nano-20k.rules 解绑 ftdi_sio 驱动的方法。后续将覆盖开源工具链、IP、同步逻辑与内置逻辑分析仪。

本文来源:https://hackaday.com/2026-09-28/the-fpga-chronicles-exploring-the-tang-nano-20k/
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。

In the opening of the Hackaday series "FPGA Chronicles," author Al Williams announces the revival of his earlier FPGA Bootcamp tutorial, switching to the Tang Nano 20K entry-level board built around the GOWIN GW2AR-18 as the main platform.

The article first reviews the history of FPGAs: from mask-programmed and programmable ASICs that cost "a carload of money," to turning unconnected functional blocks into configurable interconnects, ultimately letting ordinary people customize chips themselves. Why use an FPGA? The traffic light in the classroom is just a demonstration of state machines; the real value scenarios, such as hundreds of digital sensors on a rocket requiring any signal to trigger an alarm within microseconds, show that a processor must sample in groups and handle interrupts, while an FPGA can directly implement a giant OR gate that continuously monitors all inputs without being preempted by other logic.

On the hardware side, the GW2AR-LV18QN88C8/I7 contains 20736 four-input lookup tables (LUT4) and 15552 flip-flops; with a reasonable pipelined design, it can run stably at low hundreds of megahertz. The chip's standout feature is memory: it has both distributed RAM and block RAM, and packages a separate 8MB 32-bit SDR SDRAM. The board also offers 48 18×18 multipliers, a programmable clock generator, 64Mbit QSPI Flash, and audio, LCD, microSD, and HDMI interfaces; the onboard MCU can be used to program the clock generator, perform JTAG downloads, and provide a virtual serial port.

The tutorial then demonstrates the complete flow: defining logic in Verilog, creating a top-level module, writing pin constraints (IO_LOC / IO_PORT), synthesis, place-and-route to generate a bitstream, and downloading to RAM or configuration Flash. The author also shares pitfalls encountered with GOWIN IDE on Linux (libfreetype conflicts, LD_LIBRARY_PATH settings), as well as a method to unbind the ftdi_sio driver via /etc/udev/rules.d/99-tang-nano-20k.rules. Future installments will cover the open-source toolchain, IP, synchronous logic, and the built-in logic analyzer.

FPGA Chronicle: A Detailed Look at the Low-Cost, Open-Source-Friendly Tang Nano 20K (GOWIN GW2AR-18)

暂无评论,快来发表第一条评论吧!No comments yet. Be the first!

📮 需求咨询📮 Inquiry