Geekworm UPS Scap 5V5A:树莓派 5 超级电容 UPS HAT,断电后从容保存数据




Geekworm 与 Mcuzone 合作推出 UPS Scap 5V5A,这是一款为树莓派 5 设计的超级电容 UPS HAT。它的设计目标不是提供数小时的备电,而是让树莓派能多支撑几秒到几分钟,以便保存数据并安全关机。
该 HAT 提供 100F、60F 与 22F 三种容量版本,内置 PD 芯片可协商出真正的 5V/5A 输出。这足以让树莓派 5 稳定运行,而不会触发某些电源可能引发的低压警告。模块通过 pogo 针连接树莓派 5 以检测掉电,并支持 I2C 以实时读取电压与电流。
它还具备双独立供电输入,既可用宽压 DC 圆口供电,也可用标准 USB-C PD 充电器供电,两种充电输入不可同时使用。输出侧为带内置 PD 握手协议的 USB Type-C 口(可绕过受限外设的 Low Power 警告)与标准 USB Type-A 口,两口合计最高输出 5V/5A,并提供可选的 pogo pin 输出(出厂未焊)。
工作模式可通过硬件焊盘切换:长续航模式(焊点 L,截止电压 1.6V)与性能模式(焊点 P,截止电压 2.4V)。此外还配有主输出电源开关、放电按钮与放电指示 LED(用于安全释放电容电量)、5 级电量指示 LED 与主电源指示 LED。
监测与控制通过 GPIO26 与 I2C 完成:GPIO26 负责检测外部供电状态,板载 INA219 则通过 I2C 提供超级电容电压与充放电电流的实时读数。官方还提供了掉电检测的参考脚本。
规格方面,兼容树莓派 5(也可通过标准 USB 输出向下兼容树莓派 4B、3B 与 Orange Pi),尺寸为 85 × 56 mm,供电为 9V–24V DC(5.5 × 2.1 mm 圆口)或 12V USB Type-C PD。
本文编译自英文原文:https://www.cnx-software.com/2026/10/05/geekworm-ups-scap-5v5a-a-supercapacitor-ups-hat-for-raspberry-pi-5/
本文来源:https://www.cnx-software.com/2026/10/05/geekworm-ups-scap-5v5a-a-supercapacitor-ups-hat-for-raspberry-pi-5/
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。

Geekworm, in collaboration with Mcuzone, has launched a new supercapacitor UPS HAT for the Raspberry Pi 5 designed to keep the Raspberry Pi running long enough (a few seconds to a few minutes) to save data and shut down safely, rather than provide hours of backup power.
Available in 100F, 60F, and 22F versions, the HAT has a built-in PD chip that negotiates a true 5V/5A output. This gives the Raspberry Pi 5 enough power to run properly without triggering the low-voltage warnings that can happen with some power supplies. The module connects to the Raspberry Pi 5 through pogo pins to detect power loss and supports I2C for checking voltage and current in real time. It also features dual independent power inputs, so you can power it with either a wide-voltage DC barrel jack or a standard USB-C PD charger.

Geekworm UPS Scap 5V5A supercapacitor UPS HAT specifications: Compatibility – Raspberry Pi 5 (Back-compatible with Raspberry Pi 4B, 3B, and Orange Pi via the standard USB output) Supercapacitor options – 100F, 60F, 22F 9V–24V DC via 5.5 × 2.1 mm barrel connector 12V via USB Type-C PD input Only one charging input (DC or USB-C) should be used at a time USB Type-C port with built-in PD handshake to bypass restricted peripheral “Low Power” warnings Total shared output of up to 5V / 5A across both ports Unpopulated Pogo Pin output option Operating modes – Hardware solder pads to switch between:
Long-endurance Mode (Solder point L) with a 1.6V cutoff Performance Mode (Solder point P) with a 2.4V cutoff Hardware discharge button paired with a discharge indicator LED (to safely drain the cap) 5-level capacity LED indicators and a main power indicator LED I2C pins for INA219-based supercapacitor voltage and current monitoring Power loss detection pin (GPIO26) to signal when external power drops Wake-up/sleep pin for power recovery signaling Geekworm Raspberry Pi 5 supercapacitor UPS HAT hardware overview UPS Scap 5V5A powering a Raspberry Pi 5 The supercapacitor UPS HAT supports software-based power management through GPIO26 and I2C. GPIO26 detects external power status, whereas the onboard INA219 provides real-time supercapacitor voltage and charge/discharge current readings over I2C. The company also provides reference scripts for power-loss detection, monitoring, automatic shutdown, and power recovery/wake-up on Raspberry Pi OS and Ubuntu, although they mention that the supplied shutdown example should be tested and adapted before unattended use. More information is available on the Unlike traditional 18650 lithium-ion UPS boards, like the , this module uses supercapacitors instead of batteries. The 100F version provides only about 9 seconds at 5V/5A, but can run for up to 3.5 minutes at 0.5A in Long Endurance Mode. This makes it better suited for short power cuts or giving the Raspberry Pi enough time to shut down safely and avoid SD card corruption. The trade-off is a much longer lifespan of over 500,000 charge cycles, faster charging in around 15 minutes, and no battery-related fire or chemical leakage concerns.
Supercapacitor duration based on capacity, power draw, and selected mode The Geekworm supercapacitor UPS HAT for Raspberry Pi 5 is available on AliExpress for $41.00 , the 22F version costs $44.90, the 60F version costs $46.90, and the 100F version costs $48.90. The package includes the main UPS module, standoffs, and a U-shaped USB-C-to-C adapter board for routing power to the Raspberry Pi. Geekworm also has , so the Supercapacitor HAT may soon be available there as well.
Debashis Das is a technical content writer and embedded engineer with over five years of experience in the industry. With expertise in Embedded C, PCB Design, and SEO optimization, he effectively blends difficult technical topics with clear communication