台式激光器升级到兆瓦级峰值功率:Q 开关把脉冲压到 14 纳秒

脉冲激光有趣的一点在于:虽然平均功率可能只有几瓦甚至几毫瓦,但峰值功率很容易达到平均值的数百万倍。这在正常工作中就会发生;而如 Les’ Lab 所展示的,加入 Q 开关可以显著提升峰值功率。
Q 开关是一种光学衰减器,置于激光谐振腔内时,它会阻止腔体达到谐振,从而大幅限制受激辐射,使能量随着增益介质逐渐饱和而不断累积。最终在某个能量水平上,Q 开关突然不再阻挡光,腔体以一个极短极强的脉冲起振。Q 开关并不会增加单次激光的总能量,但能让能量释放得更快。
在这个案例中,Les 使用了掺铬钇铝石榴石(Cr:YAG)晶体作为 Q 开关,并对比了多种不同晶体的性能表现。
Les 使用两个传感器测量激光脉冲:一个热释电能量传感器,以及一个用于测量脉冲形状的快速光电二极管。不加 Q 开关时,Les 的激光脉冲长度约 150 微秒,总能量约 137 mJ,峰值功率略低于 1 千瓦。加入 Q 开关后,脉冲缩短到 14 纳秒,峰值功率升至 1.3 兆瓦,但总能量下降到 77 mJ。
Les 还制作了一台吸收率计,用它对比了不同吸收率的多款 Q 开关。总体规律是:吸收率越高,激光起振时的峰值功率越高,在 92% 吸收率时达到 2.25 MW。
不过峰值功率提升并未转化为更强的切割能力——瞄准金属目标时,脉冲太短,除了烧蚀金属表面之外做不了更多。但其能量输出仍足以在激光焦点处电离空气或击碎玻璃。
这只是 Les 对原有纹身去除激光器所做的诸多改造之一,这次升级是建立在此前对增益介质本身的改造基础上的。
本文编译自英文原文:https://hackaday.com/2026/10/04/upgrading-a-benchtop-laser-for-megawatt-power/
本文来源:https://hackaday.com/2026/10/04/upgrading-a-benchtop-laser-for-megawatt-power/
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。

One fascinating thing about a pulsed laser is that, though the average power may be measured in watts or milliwatts, the peak power can easily reach millions of times that. This happens even in normal operation, but as [Les’ Lab] demonstrated, adding a can considerably enhance the peak power.
A Q-switch is an optical attenuator; when placed in the laser cavity, it keeps the cavity from reaching resonance. This greatly limits stimulated emission, allowing energy to build up in the chamber as the gain medium becomes increasingly saturated. Eventually, at some energy level, the Q-switch suddenly stops blocking light, and the cavity lases in a very short, powerful pulse. The Q-switch doesn’t increase the energy in a laser shot, but it does release it much more quickly. In this case, [Les] used chromium-doped yttrium aluminum garnet crystals as the Q-switch and compared performance across several different crystals.
[Les] used two sensors to measure the laser pulse: a pyroelectric energy sensor and a fast photodiode to measure the pulse’s shape. Without the Q-switch, [Les]’s laser produced a pulse about 150 µs long, with a total energy of about 137 mJ and a peak power just under one kilowatt. After adding a Q-switch, the pulse dropped to 14 ns, and the peak power rose to 1.3 megawatts, though the total energy dropped to 77 mJ. [Les] also built an absorption meter and used this to compare several Q-switches with different absorptions; in general, greater absorption increased the peak power when the laser did fire, reaching 2.25 MW at 92% absorption. Increased peak power didn’t translate into greater cutting power, though; when aiming at a metal target, the pulse was too short to do much more than ablate the metal’s surface. The energy output was, however, enough to ionize air or shatter glass at the laser’s focal point.
This isn’t the only enhancement [Les] made to his former ; this builds on a previous upgrade itself. For more background on why Q-switches work, check out our article on