
如果你读 Hackaday 有些年头,一定见过黑客把设备原厂固件换成开源替代方案的玩法。多数时候这么做是为了获得更多功能,或是解除某些莫名其妙的限制。但如果你打算给 Onkyo TX-NR717 这样的 AV 功放刷入 OSIRIS,动机恐怕只有一个——把机器救活。
正如开发者 Jokūbas 所解释的,部分采用德州仪器 D830 芯片的 Onkyo 功放存在一个非常具体的故障:机器能开机、看起来一切正常,但就是没有声音。出现这种状况,要么是 D830 本身损坏,要么是存放其固件的 64 MiB NAND 闪存被"烤熟"了。不幸的是,更换其中任何一个元件都比想象中麻烦。
一切都经过这颗 TI D830。它一坏,你就头疼。
如果你换上一颗更容易买到、更耐坏的引脚兼容芯片,原厂固件将无法启动。如果你尝试更换 NAND,会发现原版软件只能寻址 512 字节页,而如今市面上能买到的闪存用的都是 2 KiB 或 4 KiB 页。这两种情况下,都得靠 OSIRIS 救场。
这款开源固件不仅支持 OMAP-L137 等 D830 兼容芯片,还能寻址现代 NAND 闪存,更换单个或两个元件都变得现实得多。装上新硬件再刷入新固件,你的 Onkyo 功放就能重获新生。不过话说回来,OSIRIS 的功能还不完整,功能清单里标注"未测试/未实现"的条目目前多过真正可用的条目——但好歹是个开始。
当然,并非功放上所有烧坏的部件都需要刷固件来更换。有时候机器闹脾气,只需要换掉几个无源元件——今年 3 月我们就报道过一例多故障 Onkyo 功放的修复。
本文来源:https://hackaday.com/2026/10/13/open-firmware-fixes-dead-onkyo-av-receivers/
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。
If you've been reading Hackaday for any length of time, you'll know we love seeing hackers replacing the stock firmware on their devices with open source alternatives. Usually this is done because the open firmware offers more features, or lifts some arbitrary limitation. But if you find yourself installing OSIRIS on an Onkyo AV receiver such as the TX-NR717, it's probably because you're trying to bring the thing back to life.
As developer Jokūbas explains, certain Onkyo receivers that use the Texas Instruments D830 are known to suffer from a very specific failure — the device will power on and appear functional, but no audio will come through. When this happens, it's either because the D830 itself has failed or the 64 MiB NAND flash chip that holds the firmware it runs is cooked. Unfortunately, replacing either component is a bit more difficult than you might expect.
Everything passes through the Texas Instruments D830. If it goes, you've got a problem.
If you swap the D830 with a pin-compatible chip that's easier to find and less prone to failure, the stock firmware won't boot. If you try to replace the NAND, you'll find that the original software is only capable of addressing 512-byte pages, while the flash you'll find on the market today uses 2 KiB or 4 KiB pages. In both cases, it's OSIRIS to the rescue.

The open firmware not only supports D830 compatible chips such as the OMAP-L137, but it's able to address modern NAND flash, making the replacement of either or both components far more practical. With fresh hardware and the new firmware installed, your Onkyo receiver should spring back to life. That said, OSIRIS isn't feature complete yet, and truthfully the items listed as untested or not implemented on the feature list currently outnumber the entries for what actually does work. But at least it's a start.
Of course, not all the burned out parts on your Onkyo receiver require a firmware flash to replace. Sometimes a misbehaving unit just needs to have a few of its passive components replaced.