VIEWE 推出 4.3 英寸 ESP32-S31 显示屏开发板:Wi-Fi 6 + 蓝牙 5.4 + 800×480 触屏,38.99 美元VIEWE launches 4.3-inch ESP32-S31 display development board


AI free token/AI免费积分

VIEWE 近日推出了型号为 PLCM-UES31S043H800V480C-U 的 4.3 英寸智能显示屏模组,这似乎是首款采用乐鑫新款 ESP32-S31 MCU 的第三方开发板。

VIEWE ESP32-S31 开发板

该开发板集成一块 4.3 英寸显示屏,搭载 2.4 GHz Wi-Fi 6、蓝牙 5.4(LE 与 Classic)以及面向 Zigbee 和 Thread 的 IEEE 802.15.4 无线连接;同时提供 USB-C 与 USB-A 接口、microSD 卡槽、RS485 与 CAN 总线接口,以及带 UART 和 I2C 的 20 针 GPIO 扩展排针。音频方面配备 ES8389 音频编解码器、两颗 NS4150B 放大器、两个板载麦克风、四个 ADC 按键和一颗 WS2812B RGB LED;整机采用 5V 供电,工作温度范围 -20°C 至 +70°C。

核心规格上,无线模组为 ESP32-S31-WROOM-3-N16R16V:SoC ESP32-S31NRV16 集成 RISC-V HP 高性能 RV32IMAFCP 核心(320 MHz,带 FPU、SIMD)与 RISC-V LP 低功耗 MCU 核心;512 KB SRAM + 32 KB 低功耗 SRAM,并罕见地配备了 16MB PSRAM;16MB flash。显示屏为 4.3 英寸 IPS TFT LCD,800×480 分辨率、RGB 竖排像素排列、1620 万色、400 cd/m² 亮度,经 40 针 24 位 RGB 接口由 ST7262E43-G4 驱动 IC 驱动,配 GT911 电容触控。

由于 ESP32-S31 仍处于预览阶段,目前只能使用 ESP-IDF 框架编程,且需要带 --preview 参数的 master 分支。官方在 GitHub 上提供了 LCD、触控面板、ES8389 音频播放、SD 卡、RS485/CAN 等示例以及一套完整的 LVGL 工厂 UI。乐鑫去年 8 月已发布 ESP32-S31 的 Linux BSP 开发者预览,未来 Linux 支持亦有可能。

该开发板在 VIEWE 商店售价 38.99 美元,预计近日内上架该公司速卖通店。对于需要"MCU + 彩屏 + 无线"一体化 HMI 方案的嵌入式开发者而言,这类带 LVGL 示例的成套模组可以显著缩短智能面板类产品的开发周期。

本文来源:https://www.cnx-software.com/2026/10/14/viewe-4-3-inch-esp32-s31-display-development-board/
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。

VIEWE has introduced the PLCM-UES31S043H800V480C-U, a 4.3-inch smart display module that appears to be the first third-party development board powered by the new ESP32-S31 MCU.

The board includes a 4.3-inch display with 2.4 GHz Wi-Fi 6, Bluetooth 5.4 LE and Classic, and IEEE 802.15.4 for Zigbee and Thread. It also features USB-C and USB-A ports, a microSD card slot, RS485 and CAN interfaces, and a 20-pin GPIO expansion header with UART and I2C. The board also includes an ES8389 audio codec, two NS4150B amplifiers, two onboard microphones, four ADC buttons, a WS2812B RGB LED, and BOOT/RESET buttons. It operates on a 5V power supply and supports an operating temperature range of -20C to +70C.

The wireless module is an ESP32-S31-WROOM-3-N16R16V with the ESP32-S31NRV16 SoC: a RISC-V HP (High-performance) RV32IMAFCP CPU @ 320 MHz with FPU and SIMD, plus a RISC-V LP (Low-power) MCU core. It comes with 512 KB SRAM, 32 KB low-power SRAM, 16MB PSRAM, and 16MB flash. Wireless connectivity covers 2.4 GHz WiFi 6 (802.11ax), Bluetooth 5.4 with LE Audio, direction finding, Bluetooth Mesh 1.1 and Classic, plus an 802.15.4 radio for Zigbee, Thread and Matter.

The display is a 4.3-inch IPS TFT LCD with 800 x 480 resolution, RGB Vertical Stripe pixel arrangement, 16.2M colors and 400 cd/m2 brightness, connected over a 40-pin 24-bit RGB interface via the ST7262E43-G4 driver IC, with a GT911 capacitive touch panel. Audio is handled by an Everest ES8389 stereo codec with 2x NS4150B Class-D speaker amplifiers and two onboard microphones. The board also provides a USB Type-C port for 5V power, programming and serial debug via CH340C, a USB 2.0 Type-A High-Speed port, RS485 and CAN on a 6-pin terminal block, a 2x10-pin external GPIO header, four ADC keys, a WS2812B RGB LED and a 3 kHz buzzer.

VIEWE ESP32-S31 开发板

Since the ESP32-S31 is still a preview device, you can program it only with the ESP-IDF framework, using the ESP-IDF master branch with the -preview flag. The company provides examples, including LCD, touch panel, ES8389 audio playback, SD card access, RS485/CAN interfaces, and a complete LVGL factory UI on GitHub. Linux support might eventually be a possibility, since Espressif released an ESP32-S31 Linux BSP developer preview last August.

VIEWE 4.3-inch ESP32-S31 display development board is sold for $38.99 on the VIEWE store, and should become available on the company's AliExpress store in the next few days.

暂无评论,快来发表第一条评论吧!No comments yet. Be the first!

📮 需求咨询📮 Inquiry