M5Stack PaperDIY 套件发布:ESP32-S3 配 4.7 英寸电子纸,25 美元起M5Stack PaperDIY Kits pair an ESP32-S3 MCU with a 4.7-inch e-Paper display


AI free token/AI免费积分
M5Stack PaperDIY 套件发布:ESP32-S3 配 4.7 英寸电子纸,25 美元起

【产品开发】CNX Software 报道,M5Stack 发布了 PaperDIY 系列——2020 年 M5Paper ESP32 开发套件的升级版本,核心升级为 ESP32-S3 微控制器和一块 4.7 英寸、支持 16 级灰度的电子纸显示屏。

该系列分为两个版本:PaperDIY Complete Kit 为工厂组装好的成品,配 3D 打印外壳;PaperDIY Assembly Kit 则面向集成进自定义项目的用户。两块板子均带有 microSD 卡槽、内置 140mAh 电池,以及定制的 M5PM1 低功耗管理芯片。

主要规格方面,核心模组为 ESP32-S3-WROOM-1-N16R8:双核 LX7 处理器最高 240MHz,512KB SRAM、8MB Octal PSRAM、384KB ROM,支持 WiFi 4 与蓝牙 5.0 LE,配备 16MB flash 与 PCB 天线。显示屏为 4.7 英寸(960×540)ED047TC1 电子纸,16 级灰度,8 位并行接口可直接控制,表面由亚克力面板保护。其他接口包括 USB Type-C(供电与烧录)、两路 FPC 0.5mm 12Pin 扩展口(引出 I2S 与 SPI 信号),以及一颗电源键和两颗用户按键。

供电部分支持 5V USB 或电源焊盘输入,内置 140mAh 3.7V 锂电池(SH1.0-2P 接口),M5PM1 电源管理芯片负责监控电池与 USB 电压、控制电子纸升压电路,功耗为 40.95mA@4.2V,峰值可达 161mA。尺寸方面,Assembly Kit 为 115.3×62.5×5.5mm、重 26.4 克;Complete Kit 为 120×68.2×6.3mm、重 43.1 克,工作温度 0-40℃。

软件上,M5Stack 支持 Arduino IDE,提供 M5Unified 与 M5GFX 库进行硬件与显示控制,并有独立的 M5PM1 电源管理库。官方还提供基于 ESP-IDF 的出厂固件源码,涵盖电池监控、Wi-Fi 扫描、microSD 访问与按键操作等示例;目前支持通过 M5Stack WebBurner 烧录,UiFlow 图形化编程尚未支持。原理图、引脚映射、数据手册与外壳设计文件可在官方文档中获取。

与 2020 年的 M5Paper 相比,新版去掉了触控屏与传感器,但升级到 ESP32-S3。此前 CNX 也介绍过 LILYGO 的 T5 4.7 英寸 E-Paper S3 Pro,同样采用 ED047TC1 显示屏与 ESP32-S3,但扩展选项不同,并提供可选的 18650 电池座。

需要注意的一个细节是:官方文档对 Complete Kit 的 M2 安装孔有「螺丝规格警告」——螺丝螺纹长度必须小于 3mm,过长的螺丝会顶压电子纸显示屏并造成永久性损坏。

售价方面,PaperDIY Assembly Kit 在 AliExpress 与官方商店售价 25 美元,Complete Kit 官方售价 29.90 美元(目前缺货)。

本文来源:https://www.cnx-software.com/2026/10/18/m5stack-paperdiy-kits-pair-an-esp32-s3-mcu-with-a-4-7-inch-e-paper-display/
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。

M5Stack has released the PaperDIY series, an updated version of its 2020 M5Paper ESP32 development kit, featuring an ESP32-S3 MCU and a 4.7-inch e-paper display with 16 levels of gray.

It comes in two versions: the PaperDIY Complete Kit, which ships factory-assembled in a 3D-printed enclosure, and the PaperDIY Assembly Kit, which is designed to be integrated into custom projects. Both boards also include a microSD card slot for extended storage, a built-in 140mAh battery, and a custom M5PM1 low-power management chip.

The core module is an ESP32-S3-WROOM-1-N16R8 with a dual-core LX7 processor at up to 240MHz, 512KB SRAM, 8MB Octal PSRAM, 384KB ROM, WiFi 4 802.11b/g/n and Bluetooth 5.0 LE connectivity, 16MB flash, and a PCB antenna. Storage is expandable via a microSD card slot.

The display is a 4.7-inch (960 x 540) ED047TC1 e-paper display with 16-level grayscale and an 8-bit parallel interface for direct display control, protected by an acrylic screen pressure plate. A USB Type-C port handles power and programming, and two FPC 0.5mm 12-pin interfaces expose I2S and SPI signals. There's one power button (single click for power on/reset, double click for power off, long press for download mode) and two user buttons.

Power is supplied via 5V over USB Type-C or 5V power pads, with a built-in 140mAh 3.7V lithium battery with SH1.0-2P connector. The M5PM1 power management IC monitors battery and USB voltage and controls the e-paper boost circuit. Consumption is 40.95mA at 4.2V, with peaks up to 161mA.

M5Stack PaperDIY Kits pair an ESP32-S3 MCU with a 4.7-inch e-Paper display

The Assembly Kit measures 115.3 x 62.5 x 5.5 mm and weighs 26.4 grams, while the Complete Kit measures 120 x 68.2 x 6.3 mm, weighs 43.1 grams, and ships in a 3D-printed PLA enclosure. Operating temperature ranges from 0 to 40 degrees Celsius.

On the software side, M5Stack supports Arduino IDE and provides the M5Unified and M5GFX libraries for hardware and display control, along with a separate M5PM1 library for power management. The company also provides factory firmware source code based on ESP-IDF, including examples for battery monitoring, Wi-Fi scanning, microSD card access, and button operation. Flashing is currently supported via M5Stack's WebBurner, though UiFlow graphical programming is not mentioned. Additional resources, including schematics, pin mappings, datasheets, and enclosure design files, are available in the documentation.

The original M5Paper was released back in 2020 with a similar 4.7-inch grayscale e-paper display, touchscreen support, sensors, and a larger battery, but was built around a generic ESP32. The new PaperDIY drops the touchscreen and sensors but upgrades to an ESP32-S3. A similar product from LILYGO, the T5 4.7-inch E-Paper S3 Pro, uses the same ED047TC1 display and ESP32-S3 but features different expansion options, including an optional 18650 battery holder.

One crucial warning from the documentation: for the Complete Kit's M2 mounting holes, screws must have a thread length of less than 3mm. Using longer screws will press against the e-paper display and permanently damage it.

The M5Stack PaperDIY Assembly Kit is available on AliExpress and the company's official store for $25. The Complete Kit costs $29.90 on the official store, but is currently out of stock.

暂无评论,快来发表第一条评论吧!No comments yet. Be the first!

📮 需求咨询📮 Inquiry