华为 20 几块的墨水屏壳被逆向火了 三条点亮路线、墨印 MoInk(ESP32-C3 直驱)Huawei's 20-something-yuan e-ink case goes viral from reverse engineering: three boot routes, MoInk (ESP32-C3 direct drive)


AI free token/AI免费积分
华为 20 几块的墨水屏壳被逆向火了 三条点亮路线、墨印 MoInk(ESP32-C3 直驱)

华为 20 几块的墨水屏壳被逆向火了:三条点亮路线、墨印 MoInk(ESP32-C3 直驱)

10 月 16 日晚,一条 UP 主粉丝仅一千出头的视频在 B 站冲破 10 万播放:UP 主"氧化钙硼"把华为官方墨水屏手机壳的 NFC 通信协议整个扒了出来——认证 PIN、压缩算法、刷新指令全部复现,上位机工具直接开源。评论区最扎眼的一条不是"大佬牛",而是"现在 25 了,涨到 30 指日可待"。十天内,三拨玩家先后把驱动方案卷到了开源:手机 NFC 直接刷、PN532 上位机、拆屏接 ESP32-C3 直驱,路线全齐、坑也全踩了一遍。

这块屏来自华为官方周边"墨有引力"墨水屏手机壳(中邮通讯制造,适配 nova 14 到 16 系列):3.98 英寸、552×768 分辨率、黑/白/黄/红四色电子墨水,壳内无电池,靠手机 NFC 反向供电完成写入和刷新。因又重又厚,大量壳子流进闲鱼和拼多多,二手价只要二三十块,行情正从 20 爬向 25。

路线一:不拆壳,手机 NFC 直接刷(零焊接)。手机 NFC 线圈给壳里的屏供电+传数据,壳子原封不动。华为支持特殊寻址的机型可直接用;非华为安卓可用开源 APP(GitHub: huawei-nfc-eink-android-app)。兼容性有些玄学,红米 K90 Pro Max、小米 17 Pro 等成功,真我 GT8 等失败。

路线二:PN532 上位机(零焊接,但要买模块)。买一块 PN532 NFC 模块(十几二十块)连电脑串口,跑开源的 Windows 图形工具(huawei-epd-pn532),四色预览、抖动算法、亮度对比度都能调,5 字节认证 PIN 已内置,双击即用。注意 PN532 射频功率不够需自加电容;项目许可证为 PolyForm Noncommercial,只许非商用。

路线三:拆屏 + ESP32-C3 直驱(最万能,门槛最高)。把屏从壳里拆出,用一块约 10 元的 ESP32-C3 SUPERMINI 走 SPI 直接驱动,得到真正可编程的四色墨水屏。目前最完整开源方案是 10 月 20 日发布的"墨印 MoInk"(github.com/atunverse/moink):ESP32-C3 开 WiFi 热点,手机连上自动弹出创作页,选图、裁剪、风格化、加文字全在浏览器本地完成,150mAh 电池纯休眠待机一周,接线锁死为 SCK→GPIO4、MOSI→GPIO6、CS→GPIO7、DC→GPIO1、RST→GPIO3、BUSY→GPIO10;免飞线 PCB 与超薄驱动板也已开源到立创平台,外壳模型在 MakerWorld 可直接打。

六个坑:① 别买 Pro/Ultra 版壳(线圈沿摄像头一圈,拆完手机识别不到);② 拆屏要有耐心和热源(热风枪/3D 打印热床/热水泡,漆包线极脆);③ A0/A1 是两个批次,刷固件注意选对;④ 带 CH340 自动下载的 C3 板烧录用 USB 模式而非 UART;⑤ 刷新一张图要十几秒,动图基本没戏(已有 TXT 阅读器"墨读"优化传输);⑥ 四色里没有蓝,灰色偏蓝、肤色易红,墨印专门写了 eink-warm 算法压肤色偏红。

成本算账:壳子 20–28 元 + ESP32-C3 SUPERMINI 约 10 元,总成本三四十元得一块 3.98 英寸 552×768 四色墨水屏,对比微雪同尺寸三色模块零售一百五上下,是目前最便宜的大面积四色墨水屏入场券。适合有兼容安卓机的白嫖党、想做桌面相框/冰箱贴且会焊两下的玩家、以及想啃 NFC 协议的硬件党;想当电子书阅读器或倒卖成品赚钱的两类人则劝退。

本文来源:https://post.m.smzdm.com/p/awwolv9g
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。

Huawei 20-something yuan e-ink case goes viral after reverse engineering: Three activation routes, MoInk (ESP32-C3 direct drive)

On the evening of October 16, a video from a Bilibili UP creator with just over a thousand followers surpassed 100,000 views: The creator "Oxide Calcium Boron" completely reverse-engineered the NFC communication protocol of the official Huawei e-ink phone case—replicating the authentication PIN, compression algorithm, and refresh commands, and open-sourcing the host computer tool. The most eye-catching comment was not "big shot is awesome," but rather "It's 25 yuan now, reaching 30 is just around the corner." Within ten days, three groups of enthusiasts successively open-sourced the driver solutions: direct writing via smartphone NFC, PN532 host computer, and tearing down the screen for direct ESP32-C3 drive. All routes are covered, and all pitfalls have been stepped on.

This screen comes from the official Huawei accessory "Gravity of Ink" e-ink phone case (manufactured by China Post Communications, compatible with nova 14 to 16 series): 3.98 inches, 552×768 resolution, four-color e-ink (black/white/yellow/red). It has no internal battery and relies on reverse power supply from the smartphone's NFC for writing and refreshing. Because it is heavy and thick, many cases flooded into Xianyu and Pinduoduo, with secondhand prices as low as 20 to 30 yuan. The market price is currently climbing from 20 to 25.

Route One: Flash directly with smartphone NFC without disassembling the case (zero soldering). The smartphone NFC coil powers the screen inside the case and transfers data, keeping the case completely intact. Huawei models supporting special addressing can be used directly; non-Huawei Androids can use the open-source APP (GitHub: huawei-nfc-eink-android-app). Compatibility is somewhat hit-or-miss; Redmi K90 Pro Max and Xiaomi 17 Pro are successful, while realme GT8 fails.

Route Two: PN532 host computer (zero soldering, but requires purchasing a module). Buy a PN532 NFC module (around 10 to 20 yuan), connect it to the computer's serial port, and run the open-source Windows GUI tool (huawei-epd-pn532). It allows adjustment of four-color preview, dithering algorithms, brightness, and contrast. The 5-byte authentication PIN is built-in, making it ready to use with a double click. Note that the PN532's RF power is insufficient and requires adding capacitors yourself; the project license is PolyForm Noncommercial, strictly prohibiting commercial use.

Route Three: Tear down the screen + ESP32-C3 direct drive (most versatile, highest barrier to entry). Remove the screen from the case and directly drive it via SPI using an ESP32-C3 SUPERMINI (about 10 yuan) to obtain a truly programmable four-color e-ink screen. Currently, the most complete open-source solution is "MoInk," released on October 20 (github.com/atunverse/moink): The ESP32-C3 turns on a WiFi hotspot, and upon connecting, the smartphone automatically pops up a creation page where selecting images, cropping, stylizing, and adding text are all done locally in the browser. A 150mAh battery can last a week in pure sleep standby. The wiring is locked as SCK→GPIO4, MOSI→GPIO6, CS→GPIO7, DC→GPIO1, RST→GPIO3, BUSY→GPIO10. Flywire-free PCBs and ultra-thin driver boards have also been open-sourced on the LCSC platform, and the outer shell models can be directly printed on MakerWorld.

Six pitfalls: ① Do not buy the Pro/Ultra version cases (the coil goes around the camera, and after tearing it down, the phone cannot recognize it); ② Patience and a heat source are required to remove the screen (heat gun/3D printer heat bed/hot water soak; enameled wires are extremely fragile); ③ A0/A1 are two batches, pay attention to selecting the correct one when flashing firmware; ④ For C3 boards with CH340 auto-download, use USB mode instead of UART for firmware burning; ⑤ Refreshing an image takes over ten seconds, and animated images are basically out of the question (the TXT reader "Modu" already optimizes transmission); ⑥ There is no blue among the four colors; gray leans blue, and skin tones tend to turn red. MoInk specifically wrote the eink-warm algorithm to suppress skin tone reddening.

Cost calculation: Case 20–28 yuan + ESP32-C3 SUPERMINI about 10 yuan, totaling 30 to 40 yuan gets you a 3.98-inch 552×768 four-color e-ink screen. Compared to the Seeed Studio same-size three-color module retailing at around 150 yuan, it is currently the cheapest entry ticket for a large-area four-color e-ink screen. It suits freeloaders with compatible Android phones, hobbyists who can solder a bit and want to make desktop photo frames/fridge magnets, and hardware nerds who want to dig into NFC protocols. However, those who want to use it as an e-book reader or make money by reselling finished products are advised against it.

Huawei's 20-something-yuan e-ink case goes viral from reverse engineering: three boot routes, MoInk (ESP32-C3 direct drive)

暂无评论,快来发表第一条评论吧!No comments yet. Be the first!

📮 需求咨询📮 Inquiry