
Picotronix 是一款由总部位于悉尼的 Thort Werx Pty Ltd 推出的模块化示波器、逻辑分析仪和频率计,基于两块 Raspberry Pi Pico 2 构建——更准确地说,是使用一块 Pico 2 作为信号处理器,另一块 Pico 2 W 用于驱动显示屏并提供无线连接功能。
该方案由集成 LCD 和三个扩展端口的 Picotronix 主模块组成,用于连接 picoPods 插件扩展模块,以添加高速 ADC、混合逻辑系列逻辑状态分析、波形发生器、模拟信号调理等功能。
Picotronix 主要特性与规格:
8 通道逻辑分析仪,借助 picoPod 可扩展至最多 14 通道;最高 150 MHz 采样率
显示屏——来自 Pimoroni 的 320 × 240 彩色 LCD
三个扩展端口、两个 10-pin 模拟端口和一个 26-pin 多功能端口
模拟通道在 1 MΩ 输入阻抗下支持 3 Vpp 或 16.6 Vpp,并配有额外的 BNC AC 与 DC 输入
使用 RP2350 的 12-bit ADC 进行采集,时基范围为每格 5 ms 至 10 µs
辅助输入可兼作逻辑探头或电压表,且无需依赖任一 Pico 即可工作
供电——USB、9–12 V 电源适配器或四节 AAA 电池
8 通道逻辑分析仪,借助 picoPod 可扩展至最多 14 通道;最高 150 MHz 采样率
显示屏——来自 Pimoroni 的 320 × 240 彩色 LCD
三个扩展端口、两个 10-pin 模拟端口和一个 26-pin 多功能端口
模拟通道在 1 MΩ 输入阻抗下支持 3 Vpp 或 16.6 Vpp,并配有额外的 BNC AC 与 DC 输入
使用 RP2350 的 12-bit ADC 进行采集,时基范围为每格 5 ms 至 10 µs。
在 1 MΩ 输入阻抗下支持 3 Vpp 或 16.6 Vpp,并配有额外的 BNC AC 与 DC 输入
使用 RP2350 的 12-bit ADC 进行采集,时基范围为每格 5 ms 至 10 µs。
辅助输入可兼作逻辑探头或电压表,且无需依赖任一 Pico
供电——USB、9–12 V 电源适配器或四节 AAA 电池。
单端模拟:500 mV、1 V、2 V 和 5 V 量程窗口,可在 ±5 V 范围内任意移动,并带有一个 x10 BNC 输入,最高支持 ±50 V。
差分:2 Vpp,以及一个支持 ±25 V 共模电压的模块,提供软件切换的 x1/x10 档位。
Wave-05:一款 12-bit R2R DAC,输出范围 10 mVpp 至 3.3 Vpp,带 ±5 V 可编程偏置,并配备两个精密电压基准。
12-bit 逻辑状态分析仪:采样率为 150 MSPS,提供三个 4-bit 端口,每个端口可支持不同的逻辑电平系列(1.8、2.5、3.3 或 5 V)。
MSO-12:一款 100 MSPS 的 8-bit ADC、8 个逻辑输入,以及一个四通道 12-bit 串行 ADC,还能检测每个逻辑端口的电平系列电压。
Electronix Lab:一款教学用 picoPod,可通过线缆连接全部三个端口。你可以在该模块上配置逻辑、生成真实信号,并在显示屏上查看结果。
ADC-100 picoPod:双通道 100 MSPS ADC,在未改动的 150 MHz RP2350 上,单通道最高可支持 75 MSPS 采集,双通道最高可支持 50 MSPS 采集。
单端模拟:500 mV、1 V、2 V 和 5 V 量程窗口,可在 ±5 V 范围内任意移动,并带有一个 x10 BNC 输入,最高支持 ±50 V。
差分:2 Vpp,以及一个支持 ±25 V 共模电压的模块,提供软件切换的 x1/x10 档位。
Wave-05:一款 12-bit R2R DAC,输出范围 10 mVpp 至 3.3 Vpp,带 ±5 V 可编程偏置,并配备两个精密电压基准。
12-bit 逻辑状态分析仪:采样率为 150 MSPS,提供三个 4-bit 端口,每个端口可支持不同的逻辑电平系列(1.8、2.5、3.3 或 5 V)。
MSO-12:一款 100 MSPS 的 8-bit ADC、8 个逻辑输入,以及一个四通道 12-bit 串行 ADC,还能检测每个逻辑端口的电平系列电压。
Electronix Lab:一款教学用 picoPod,可通过线缆连接全部三个端口。你可以在该模块上配置逻辑、生成真实信号,并在显示屏上查看结果。
ADC-100 picoPod:双通道 100 MSPS ADC,在未改动的 150 MHz RP2350 上,单通道最高可支持 75 MSPS 采集,双通道最高可支持 50 MSPS 采集。
Raspberry Pi Pico 2 模块化示波器 数字示波器
Picotronix 支持使用 MicroPython 进行编程,并可直接访问 RP2350 的 PIO 状态机以获得最佳性能。后续还将提供一款 PC 模拟器,以便用户在电脑上开发 MicroPython 脚本。
虽然我们被告知“一切都是开放的”,但目前尚不清楚该项目的哪些部分属于开源,因为没有提到硬件或固件的发布;不过 Kickstarter 页面确实表明部分代码将以开源形式发布:
系统的模块化设计预期未来将由我们的团队以及开源社区逐步实现多样化的软件功能。
开源特性确保社区开发可以补充我们的工作,为增强功能提供多条开发路径。
目前文档仍然有限,暂时也找不到用户手册;不过更多技术细节可在博客文章和 YouTube 视频中找到,尤其是一段 21 分钟与 Tektronix TBS 2000 示波器的对比视频。
主模块搭载两块 Raspberry Pi Pico 2 开发板
该项目刚刚在 Kickstarter 上发起众筹,筹资目标为 10,000 澳元(约 7,000 美元)。我将使用美元等值金额表示支持档位价格。Picotronix 主模块档位需要承诺 134 美元以获得一台完整设备和一套线缆,可选 picoPods 需额外付费。其他支持档位则是包含特定 picoPods 的组合包。澳大利亚境内运费需额外支付 20 至 40 澳元,全球其他地区运费为 21 至 42 美元。预计 2027 年 3 月开始发货。
Jean-Luc 于 2010 年创立了 CNX Software,最初只是兼职项目;后来他辞去软件工程经理的工作,并在 2011 年晚些时候开始全职撰写每日新闻与评测。
支持 CNX Software!可通过加密货币捐赠,成为 Patreon 的 Patron,或在 Amazon 或 AliExpress 购买商品。我们还在文章中使用联盟链接;如果你点击这些链接并完成购买,我们将获得佣金。
Pixel Pump 是一款开源的手动贴片机(众筹)
Elecrow 的 Raspberry Pi Pico Advanced Kit 配备 32 个电子模块和 32 个项目教程
Cytron MOTION 2350 Pro——用于机器人与电机控制的 Raspberry Pi RP2350 开发板
SparkFun Pro Micro——RP2350 开发板,配备 16MB Flash、8MB PSRAM
Adafruit Feather RP2350 开发板带 HSTX 端口,可实现视频输出和显示接口
本文来源:https://www.cnx-software.com/2026/10/28/picotronix-modular-oscilloscope-and-logic-analyzer-features-two-raspberry-pi-pico-2-boards/
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。
Picotronix is a modular oscilloscope, logic analyzer, and frequency meter from Sydney-based Thort Werx Pty Ltd, based on two Raspberry Pi Pico 2 units, more exactly a Pico 2 used as a signal processor and a Pico 2 W used to drive the display and for wireless connectivity.
The solution is comprised of the Picotronix Main Module with an integrated LCD and three expansion ports, used to connect picoPods plug-in expansion modules to add high-speed ADCs, mixed-logic family logic state analysis, a waveform generator, analog conditioning, and more.
Main Module Two-channel digital storage oscilloscope 8-channel logic analyzer, expandable up to 14 channels with a picoPod; up to 150 MHz sample rate Frequency meter Display – 320 × 240 color LCD from Pimoroni Three expansion ports, two 10-pin analog ports, and one 26-pin multifunction port Analog channel Accepts 3 Vpp or 16.6 Vpp at 1 MΩ, with extra BNC AC and DC inputs Captures with the RP2350’s 12-bit ADC, with timebases from 5 ms to 10 µs per division. Auxiliary input doubles as a logic probe or voltmeter and works without either Pico Power – USB, 9–12 V plug pack, or four AAA cells.
8-channel logic analyzer, expandable up to 14 channels with a picoPod; up to 150 MHz sample rate
Three expansion ports, two 10-pin analog ports, and one 26-pin multifunction port
Analog channel Accepts 3 Vpp or 16.6 Vpp at 1 MΩ, with extra BNC AC and DC inputs Captures with the RP2350’s 12-bit ADC, with timebases from 5 ms to 10 µs per division.
Accepts 3 Vpp or 16.6 Vpp at 1 MΩ, with extra BNC AC and DC inputs
Captures with the RP2350’s 12-bit ADC, with timebases from 5 ms to 10 µs per division.
Auxiliary input doubles as a logic probe or voltmeter and works without either Pico
Optional plug-in picoPods Single-ended analog: 500 mV, 1 V, 2 V and 5 V windows, movable anywhere within ±5 V, plus a x10 BNC input to ±50 V. Differential: 2 Vpp, and a ±25 V common-mode pod with software-switched x1/x10 ranges. Wave-05: a 12-bit R2R DAC, 10 mVpp to 3.3 Vpp with a ±5 V programmable offset, plus two precision voltage references. 12-bit Logic State Analyser: sampled at 150 MSPS, in three 4-bit ports that can each serve a different logic family (1.8, 2.5, 3.3 or 5 V). MSO-12: a 100 MSPS 8-bit ADC, 8 logic inputs, and a four-channel 12-bit serial ADC that also detects each logic port’s family voltage. Electronix Lab: a teaching picoPod that connects by cable to all three ports. Configure logic on the pod, generate a real signal from it, and see the result on the display. ADC-100 picoPod: dual 100 MSPS ADCs, capturing up to 75 MSPS on one channel or 50 MSPS on both on a stock 150 MHz RP2350.
Single-ended analog: 500 mV, 1 V, 2 V and 5 V windows, movable anywhere within ±5 V, plus a x10 BNC input to ±50 V.
Differential: 2 Vpp, and a ±25 V common-mode pod with software-switched x1/x10 ranges.
Wave-05: a 12-bit R2R DAC, 10 mVpp to 3.3 Vpp with a ±5 V programmable offset, plus two precision voltage references.
12-bit Logic State Analyser: sampled at 150 MSPS, in three 4-bit ports that can each serve a different logic family (1.8, 2.5, 3.3 or 5 V).
MSO-12: a 100 MSPS 8-bit ADC, 8 logic inputs, and a four-channel 12-bit serial ADC that also detects each logic port’s family voltage.
Electronix Lab: a teaching picoPod that connects by cable to all three ports. Configure logic on the pod, generate a real signal from it, and see the result on the display.

ADC-100 picoPod: dual 100 MSPS ADCs, capturing up to 75 MSPS on one channel or 50 MSPS on both on a stock 150 MHz RP2350.
Raspberry Pi Pico 2 modular oscilloscope digital oscilloscope
The Picotronix is programmable in MicroPython with direct access to the RP2350’s PIO state machines for optimal performance. A PC emulator will also be available to develop MicroPython scipts on your computer.
While we were told that “everything is open”, it’s unclear which part of the project is open-source, since there’s no mention of hardware or firmware release, but the Kickstarter page does indicate part of the code will be open-sourced:
The system’s modular design anticipates diverse software-based functions to be implemented by both our team and the open-source community over time.
The open-source nature ensures community development can supplement our efforts, providing multiple development pathways for enhanced functionality.
Documentation is currently limited, and you won’t find a user manual as of now, but more technical details are available in blog posts and YouTube videos, notably a 21-minute comparison to a Tektronix TBS 2000 oscilloscope .
The project has just launched on Kickstarter with a $10,000 AUD (about $7,000 US) funding target. I’ll use the USD equivalent for rewards’ prices. The Picotronix Main Module reward requires a $134 pledge for a full unit and a cable set, and optional picoPods are available at an extra cost. Other rewards are bundles with specific picoPods. Shipping adds $20 to $40 AUD to Australia, and $21 to $42 USD to the rest of the world. Deliveries are expected to start by March 2027.
Jean-Luc started CNX Software in 2010 as a part-time endeavor, before quitting his job as a software engineering manager, and starting to write daily news, and reviews full time later in 2011.
Support CNX Software! Donate via cryptocurrencies , become a Patron on Patreon, or purchase goods on Amazon or Aliexpress . We also use affiliate links in articles to earn commissions if you make a purchase after clicking on those links.
Pixel Pump is an open-source, manual pick-and-place machine (Crowdfunding)
Elecrow’s Raspberry Pi Pico Advanced Kit ships with 32 electronics modules, 32 project tutorials
Cytron MOTION 2350 Pro – A Raspberry Pi RP2350 board for robotics and motor control
SparkFun Pro Micro – RP2350 development board comes with 16MB flash, 8MB PSRAM
Adafruit Feather RP2350 board with HSTX port enables video output and display interfaces