
Synergy Logic SLM-RP4 工业 PLC 以 Raspberry Pi 4 SBC 为核心构建,专为工业自动化、机器控制、数据采集以及工业物联网(IIoT)应用而设计。
这款支持 DIN 导轨安装的控制器支持 24V DC 输入,并配备基于 SPI 的背板,可连接多达八个 Synergy Logic I/O 模块,提供最多 128 个 I/O 点。它还具备千兆以太网、WiFi 5、蓝牙 5.0、多个 USB 端口、两个 micro-HDMI 输出以及无风扇铝制外壳。系统运行 Raspberry Pi OS,并预装 OpenPLC,以支持标准的 IEC 61131-3 逻辑编程。
Synergy Logic SLM-RP4 规格:
SBC – Raspberry Pi 4 Model B(2GB RAM)
存储 – 16GB microSD 卡
视频 – 2 个 micro-HDMI 端口
网络 – 千兆以太网端口;双频 WiFi 5(802.11ac);蓝牙 5.0/BLE
USB – 2 个 USB 3.0 Type-A 端口;2 个 USB 2.0 Type-A 端口;1 个 USB-C 端口用于辅助供电
I/O 扩展 – 基于 SPI 的背板,支持多达八个可堆叠的 SLM 模块(18 款兼容模块型号,最多 128 个 I/O 点)
离散量输入 – 最多 16 通道 12–24V DC 或 24V AC/DC 输入,或 8 通道 100–240V AC 输入
输入模拟器 – 八通道拨动开关模块
离散量输出 – 最多 15 通道源型或漏型 DC 输出
继电器输出 – 8 通道或 16 通道继电器模块,带 SPST 或 SPDT 触点
组合式离散 I/O – 混合数字输入/输出及继电器模块
模拟量输入 – 八通道 0–10V 或 0–20mA 输入,13 位分辨率
模拟量输出 – 八通道 0–10V 或 4–20mA 输出,12 位分辨率
组合式模拟 I/O – 四个模拟输入(13 位)和两个模拟输出(12 位)
温度输入 – 四通道热电偶,支持 J、E、K、R、S、T、B、N 和 C 类型,以及毫伏输入
其他 – PWR 和 BASE 状态 LED;可编程 RGB 状态 LED;用于 PLC 运行/停止或自定义功能的拨动开关;硬件看门狗
电源 – 通过接线端子输入 24V DC Class 2(±25%);通过 USB-C 提供 5V/3A(仅控制器,不包含 I/O 背板)
温度范围 – 0°C 至 50°C,无风扇
外壳 – 铝合金,开放式设备,支持 35mm DIN 导轨安装
认证 – 已列入 UL 61010 和 UL 61010-2-201;符合 EN 61131-2 和 EN 61010 标准的 CE 认证
Synergy Logic SLM RP4 工业控制器通过基于 SPI 的背板连接八个可堆叠 I/O 模块
SLM-RP4 使用基于 SPI 的背板,通过边缘连接器连接扩展模块,因此模块之间无需额外线缆。模块连接到控制器右侧,其位置决定其槽位地址。目前已有 18 款兼容模块(不支持热插拔)可供选择,包括数字 I/O、继电器、模拟电压和电流 I/O 以及热电偶输入。
在软件方面,SLM-RP4 预装了 Raspberry Pi OS、OpenPLC Runtime 以及 Synergy Logic 的 Python 和 C++ 库。它支持 OpenPLC Editor 4.3.1 或更高版本,因此可以使用 IEC 61131-3 语言进行编程,例如梯形图(LD)、结构化文本(ST)、功能块图(FBD)和指令表(IL),并支持 Python 和 C++ 功能块。编辑器还包含 SLM-RP4 硬件支持包,用于配置 I/O 模块、分配 IEC 地址以及调整 SPI 背板设置。
背板配置界面(按槽位选择模块并进行 I/O 映射)
SPI 背板支持可调节的 I/O 扫描间隔,范围从 1ms 到 1000ms,默认设置为 10ms。它还能检测通信错误,并在错误超过设定限制时停止 PLC 运行并将输出重置为零。您还可以使用提供的 Python 和 C++ 库在不使用 OpenPLC 的情况下直接控制背板,但这两种方法不能同时使用。此外还包含硬件看门狗,以帮助从应用程序故障中恢复。
Synergy Logic 还提供了集成 FUXA 的文档,FUXA 是一款开源、基于 Web 的 HMI/SCADA 平台,可通过 Modbus TCP 与 OpenPLC 或自定义应用通信。这样您可以创建包含仪表盘、指示器、滑块和趋势图的本地仪表板。文档中还包括模拟信号监控、热电偶记录、输出控制以及 Modbus TCP 通信的示例。
其他基于 Raspberry Pi 的工业控制器还包括 Industrial Shield 的 Raspberry Pi PLC Industrial Controller(同样基于 Pi 4)、EDATEC ED-PLC2010(CM4),支持多达 32 个扩展模块并搭载 CODESYS Runtime,以及 Sfera Labs Strato Pi Max(CM4)。Synergy Logic 此前曾推出 SL-RP4,这是一款基于 Raspberry Pi 4 的工业控制器,依赖外部 I/O 连接。新款 SLM-RP4 增加了集成背板,可直接将 SLM 模块连接到控制器。
Synergy Logic SLM-RP4 售价为 249 美元,扩展 I/O 模块单独出售。较早的 SL-RP4 售价为 149 美元。更多信息,包括设置指南、软件示例和模块数据手册,可在产品页面和文档网站找到。
Debashis Das 是一名技术内容撰稿人兼嵌入式工程师,在业内拥有五年以上经验。凭借在 Embedded C、PCB Design 和 SEO 优化方面的专业能力,他能够将复杂的技术主题与清晰的沟通有效结合。
本文来源:https://www.cnx-software.com/2026/10/27/synergy-logic-slm-rp4-a-raspberry-pi-4-plc-with-modular-industrial-i-o/
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。
Synergy Logic SLM-RP4 industrial PLC is built around a Raspberry Pi 4 SBC and designed for industrial automation, machine control, data acquisition, and Industrial IoT (IIoT) applications.
The DIN-rail mountable controller supports 24V DC input and an SPI-based backplane that connects up to eight Synergy Logic I/O modules, providing up to 128 I/O points. It also features Gigabit Ethernet, WiFi 5, Bluetooth 5.0, USB ports, two micro-HDMI outputs, and a fanless aluminum enclosure. The system runs Raspberry Pi OS with OpenPLC pre-installed for standard IEC 61131-3 logic programming.
Networking Gigabit Ethernet port Dual-band WiFi 5 (802.11ac) Bluetooth 5.0/BLE
USB 2x USB 3.0 Type-A ports 2x USB 2.0 Type-A ports 1x USB-C port for auxiliary power
I/O Expansion – SPI-based backplane supporting up to eight stackable SLM modules (18 compatible module models, up to 128 I/O points) Discrete inputs – Up to 16 channels of 12–24V DC or 24V AC/DC inputs, or eight channels of 100–240V AC inputs Input simulator – Eight-channel toggle switch module Discrete outputs – Up to 15 channels of sourcing or sinking DC outputs Relay outputs – 8-channel or 16-channel relay modules with SPST or SPDT contacts Combined discrete I/O – Mixed digital input/output and relay modules Analog inputs – Eight channels of 0–10V or 0–20mA inputs with 13-bit resolution Analog outputs – Eight channels of 0–10V or 4–20mA outputs with 12-bit resolution Combined analog I/O – Four analog inputs (13-bit) and two analog outputs (12-bit) Temperature inputs – Four-channel thermocouples supporting J, E, K, R, S, T, B, N, and C types, along with millivolt inputs
Discrete inputs – Up to 16 channels of 12–24V DC or 24V AC/DC inputs, or eight channels of 100–240V AC inputs
Discrete outputs – Up to 15 channels of sourcing or sinking DC outputs
Relay outputs – 8-channel or 16-channel relay modules with SPST or SPDT contacts
Combined discrete I/O – Mixed digital input/output and relay modules
Analog inputs – Eight channels of 0–10V or 0–20mA inputs with 13-bit resolution
Analog outputs – Eight channels of 0–10V or 4–20mA outputs with 12-bit resolution
Combined analog I/O – Four analog inputs (13-bit) and two analog outputs (12-bit)
Temperature inputs – Four-channel thermocouples supporting J, E, K, R, S, T, B, N, and C types, along with millivolt inputs
Misc PWR and BASE status LEDs Programmable RGB status LED Toggle switch for PLC run/stop or custom functions Hardware watchdog
Power 24V DC Class 2 input (±25%) via terminal block 5V/3A via USB-C (controller only, not the I/O backplane)
Enclosure – Aluminum, open equipment, 35mm DIN-rail mounting
Certifications – UL 61010 and UL 61010-2-201 listed; CE marked to EN 61131-2 and EN 61010 standards

Synergy Logic SLM RP4 industrial controller with eight stackable IO modules connected through an SPI-based backplane
The SLM-RP4 uses an SPI-based backplane to connect expansion modules through edge connectors, so no extra cables are needed between modules. Modules connect to the right side of the controller, and their positions determine their slot addresses. Currently, 18 compatible modules (not hot-swappable) are available, including digital I/O, relays, analog voltage and current I/O, and thermocouple inputs.
On the software side, the SLM-RP4 comes preinstalled with Raspberry Pi OS, OpenPLC Runtime, and Synergy Logic’s Python and C++ libraries. It supports OpenPLC Editor 4.3.1 or newer, so you can program the controller using IEC 61131-3 languages such as Ladder Diagram (LD), Structured Text (ST), Function Block Diagram (FBD), and Instruction List (IL), as well as Python and C++ function blocks. The editor also includes an SLM-RP4 hardware support package for configuring I/O modules, assigning IEC addresses, and adjusting SPI backplane settings.
Backplane Configuration screen (selecting modules per slot and IO mapping)
The SPI backplane supports adjustable I/O scan intervals from 1ms to 1000ms, with 10ms set by default. It also detects communication errors and can stop PLC execution and reset outputs to zero if errors exceed a set limit. You can also use the provided Python and C++ libraries to control the backplane directly without OpenPLC, but both methods cannot be used at the same time. A hardware watchdog is also included to help recover from application failures.
Synergy Logic also provides documentation for integrating FUXA , an open-source, web-based HMI/SCADA platform that communicates with OpenPLC or custom applications over Modbus TCP. This allows you to create local dashboards with gauges, indicators, sliders, and trend charts. The documentation also includes examples for analog signal monitoring, thermocouple logging, output control, and Modbus TCP communication.
Other Raspberry Pi-based industrial controllers include Industrial Shield’s Raspberry Pi PLC Industrial Controller , also based on the Pi 4, the EDATEC ED-PLC2010 (CM4) with up to 32 expansion modules and CODESYS Runtime, and the Sfera Labs Strato Pi Max (CM4). Synergy Logic previously introduced the SL-RP4 , a Raspberry Pi 4-based industrial controller that relies on external I/O connectivity. The newer SLM-RP4 adds an integrated backplane for connecting SLM modules directly to the controller.
The Synergy Logic SLM-RP4 is available for $249, with expansion I/O modules sold separately. The earlier SL-RP4 sells for $149. More information, including setup guides, software examples, and module datasheets, can be found on the product page and the documentation website .
Debashis Das is a technical content writer and embedded engineer with over five years of experience in the industry. With expertise in Embedded C, PCB Design, and SEO optimization, he effectively blends difficult technical topics with clear communication
Support CNX Software! Donate via cryptocurrencies , become a Patron on Patreon, or purchase goods on Amazon or Aliexpress . We also use affiliate links in articles to earn commissions if you make a purchase after clicking on those links.
EDATEC launches 7-inch, 10.1-inch and 15.6-inch Industrial HMI displays powered by Raspberry Pi CM5
ModBerry Industrial Automation Controllers Leverage Raspberry Pi, FriendlyELEC, and AAEON Boards and Modules
OnLogic IGN800 Industrial Raspberry Pi Edge Gateway runs Ignition Edge software
7-inch Raspberry Pi CM4-based industrial HMI offers gigabit Ethernet, RS485 Modbus, digital and analog inputs
Seeed Studio reComputer R1025-10 industrial IoT gateway supports Ethernet, RS485, 4G LTE, LoRa, Zigbee, Wi-Fi, BLE