520 MHz STM32H7P4/STM32H7P5 Arm Cortex-M7 微控制器集成硬件信号处理器(HSP),并提供可选的 Neural-ART NPU - CNX Software520 MHz STM32H7P4/STM32H7P5 Arm Cortex-M7 MCUs feature Hardware Signal Processor (HSP), optional Neural-ART NPU - CNX Software


AI free token/AI免费积分
520 MHz STM32H7P4/STM32H7P5 Arm Cortex-M7 微控制器集成硬件信号处理器(HSP),并提供可选的 Neural-ART NPU - CNX Software

意法半导体推出 STM32H7P4 和 STM32H7P5,两款面向数字电源、电机控制、工业传感和边缘 AI 应用、属于 STM32H7P 系列的 520 MHz Arm Cortex-M7 MCU。两款产品均配备用于加速数学与信号处理运算的硬件信号处理器 (HSP),STM32H7P5 还集成 85 GOPS Neural-ART NPU 支持边缘 AI 推理/TinyML。

MCU 特性包括最高 2 MB 双 bank 闪存、736 KB SRAM、2 个高分辨率定时器(最多支持 24 路 PWM 输出)、3 个高级电机控制定时器及 4 个 12 位 ADC。其他功能涵盖 CORDIC 与 FMAC 数学加速器、3 个 CAN FD 接口、USB OTG 全速接口,并通过 Octo-SPI 与 FMC 接口支持外部存储器。

32 位 Arm Cortex-M7 CPU,主频最高 520 MHz,支持双精度 FPU、DSP 指令和 MPU;32 KB 指令缓存和 32 KB 数据缓存;性能 – 2773 CoreMark(5.33 CoreMark/MHz)

32 位 Arm Cortex-M7 CPU,主频最高 520 MHz,支持双精度 FPU、DSP 指令和 MPU

性能 – 2773 CoreMark(5.33 CoreMark/MHz)

硬件信号处理器 (HSP),支持 32 位浮点,可执行矩阵/向量运算、FFT/IFFT、滤波和卷积;CORDIC 加速器,用于三角函数计算;FMAC 滤波数学加速器

硬件信号处理器 (HSP),支持 32 位浮点,可执行矩阵/向量运算、FFT/IFFT、滤波和卷积

CORDIC 加速器,用于三角函数计算

AI 加速器(仅限 STM32H7P5) – ST Neural-ART NPU,主频最高 520 MHz,算力 85 GOPS(0.085 TOPS)

1 MB 或 2 MB 双 bank 闪存,带 ECC;736 KB SRAM;192 KB ITCM SRAM;128 KB DTCM SRAM;320 KB AXI SRAM;96 KB AHB SRAM;4 KB 备份 SRAM;1 KB OTP(一次性可编程)存储器;Octo-SPI 接口,最高 100 MHz,支持 PSRAM、NOR flash、HyperRAM 与 HyperFlash;Flexible Memory Controller (FMC),支持 SRAM、PSRAM、NOR、NAND flash 和 SDRAM,数据总线最高 16 位

736 KB SRAM;192 KB ITCM SRAM;128 KB DTCM SRAM;320 KB AXI SRAM;96 KB AHB SRAM

Octo-SPI 接口,最高 100 MHz,支持 PSRAM、NOR flash、HyperRAM 与 HyperFlash

Flexible Memory Controller (FMC),支持 SRAM、PSRAM、NOR、NAND flash 和 SDRAM,数据总线最高 16 位

多达 134 个带中断功能的 GPIO,包括最多 132 个 5 V 容忍 I/O;3 个 I2C 接口,支持 SMBus/PMBus;1 个 I3C 接口;5 个 USART、5 个 UART 和 1 个 LPUART;6 个 SPI 接口,其中 3 个支持全双工 I2S;3 个 CAN FD 控制器;1 个 USB OTG 全速接口;2 个 USB Type-C Power Delivery 控制器 (UCPD);1 个 SD/SDIO/MMC 接口,最高 100 MHz;2 个 DMA 控制器 (HPDMA 和 GPDMA)

4 个 12 位 ADC,最高 5 MSPS,最多 44 通道;1 个双通道 12 位 DAC,带缓冲输出;3 个双通道 12 位 DAC 供内部使用;8 个模拟比较器;内部电压基准(1.8 V 至 2.9 V);模拟与数字温度传感器;1 个用于 PDM 麦克风的数字滤波器

4 个 12 位 ADC,最高 5 MSPS,最多 44 通道

1 个双通道 12 位 DAC,带缓冲输出

2 个高分辨率定时器 (HRTIM),最多 24 路 PWM 输出,分辨率 1.9 ns;3 个 16 位高级电机控制定时器;4 个 32 位通用定时器;9 个 16 位通用定时器;2 个 16 位基本定时器;5 个 16 位低功耗定时器;SysTick 定时器与 RTC;独立看门狗与窗口看门狗

2 个高分辨率定时器 (HRTIM),最多 24 路 PWM 输出,分辨率 1.9 ns

读出保护 (ROP) 和专有代码读出保护 (PC-ROP);主动防篡改检测,支持安全固件升级;HASH 加速器,支持 MD5、SHA-1、SHA-2 和 HMAC;32 位真随机数发生器 (TRNG),符合 NIST SP 800-90B;96 位唯一器件 ID

读出保护 (ROP) 和专有代码读出保护 (PC-ROP)

主动防篡改检测,支持安全固件升级

HASH 加速器,支持 MD5、SHA-1、SHA-2 和 HMAC

32 位真随机数发生器 (TRNG),符合 NIST SP 800-90B

内部振荡器 – 64 MHz HSI、48 MHz HSI48、4 MHz CSI 和 32 kHz LSI;外部振荡器 – 4–50 MHz HSE 和 32.768 kHz LSE;3 个带小数分频模式的 PLL

内部振荡器 – 64 MHz HSI、48 MHz HSI48、4 MHz CSI 和 32 kHz LSI

外部振荡器 – 4–50 MHz HSE 和 32.768 kHz LSE

Serial Wire Debug (SWD)、JTAG 和 4 KB 嵌入式跟踪缓冲区

电压范围 1.71 V 至 3.6 V;集成 LDO 稳压器或 SMPS 降压转换器,视具体型号而定;Sleep、Stop、Standby 和 VBAT 模式;上电复位 (POR)、掉电复位 (PDR)、可编程电压检测器 (PVD) 和欠压复位 (BOR);带充电功能的备份电池供电

集成 LDO 稳压器或 SMPS 降压转换器,视具体型号而定

上电复位 (POR)、掉电复位 (PDR)、可编程电压检测器 (PVD) 和欠压复位 (BOR)

LQFP100 – 14 × 14 mm;LQFP128 – 14 × 14 mm;LQFP144 – 20 × 20 mm;LQFP176 – 24 × 24 mm;TFBGA100 – 8 × 8 mm;UFBGA176+25 – 10 × 10 mm;部分型号可选带裸露焊盘的 LQFP

部分型号可选带裸露焊盘的 LQFP

STM32H7P4 框图(STM32H7P5 框图将增加 Neural-ART NPU)

两大 MCU 系列的主要差异在于 STM32H7P5 集成了 Neural-ART NPU。据 ST 表示,该 NPU 运行公司的基于 AI 的弧闪故障断路器 (AFCI) 模型,速度可比在 Cortex-M7 上用软件实现快 40 倍。两款 MCU 均配备硬件信号处理器 (HSP),可卸载 Cortex-M7 上的 FFT、矩阵、向量和滤波运算,降低电机控制、电源转换和工业传感等应用的 CPU 负担。ST 称,HSP 执行 FFT 运算可比 Cortex-M7 上的软件实现快五倍。

在软件支持方面,公司提供 STM32CubeH7P 软件包,内含 HAL2 和低层驱动、中间件及示例项目。用户可使用 STM32CubeMX2 进行外设配置和代码生成,用 STM32CubeIDE 开发和调试,用 STM32CubeProgrammer 烧录固件。公司还提供电机控制套件 X-CUBE-MCSDK 以及面向数字电源应用的 X-CUBE-DPOWER。

搭载 STM32H7P5II MCU 的 STM32 Nucleo 144 开发板

STM32H7P5I-DK Discovery 开发套件

本文来源:https://www.cnx-software.com/2026/11/06/520-mhz-stm32h7p4-stm32h7p5-arm-cortex-m7-mcus-feature-hardware-signal-processor-hsp-optional-neural-art-npu/
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。

STMicroelectronics has introduced the STM32H7P4 and STM32H7P5, two 520 MHz Arm Cortex-M7 MCUs part of STM32H7P family designed for digital power, motor control, industrial sensing, and edge AI applications. Both feature a Hardware Signal Processor (HSP) for accelerating mathematical and signal-processing operations, while the STM32H7P5 also includes an 85 GOPS Neural-ART NPU for Edge AI inference/TinyML.

The MCUs feature up to 2MB dual-bank flash, 736KB SRAM, two high-resolution timers with up to 24 PWM outputs, three advanced motor-control timers, and four 12-bit ADCs. Other features include CORDIC and FMAC mathematical accelerators, three CAN FD interfaces, USB OTG Full-Speed, and support for external memory through Octo-SPI and FMC interfaces.

MCU Core 32-bit Arm Cortex-M7 CPU @ up to 520 MHz with double-precision FPU, DSP instructions, and MPU 32 KB instruction cache and 32 KB data cache Performance – 2773 CoreMark (5.33 CoreMark/MHz)

32-bit Arm Cortex-M7 CPU @ up to 520 MHz with double-precision FPU, DSP instructions, and MPU

Performance – 2773 CoreMark (5.33 CoreMark/MHz)

Mathematical coprocessors Hardware Signal Processor (HSP) with 32-bit floating-point support for matrix/vector operations, FFT/IFFT, filtering, and convolution CORDIC accelerator for trigonometric calculations FMAC filter mathematical accelerator

Hardware Signal Processor (HSP) with 32-bit floating-point support for matrix/vector operations, FFT/IFFT, filtering, and convolution

CORDIC accelerator for trigonometric calculations

AI accelerator (STM32H7P5 only) – ST Neural-ART NPU @ up to 520 MHz, delivering 85 GOPS (0.085 TOPS)

Memory/Storage 1 MB or 2 MB dual-bank flash memory with ECC 736 KB SRAM 192 KB ITCM SRAM 128 KB DTCM SRAM 320 KB AXI SRAM 96KB AHB SRAM 4 KB backup SRAM 1 KB OTP (one-time programmable) memory Octo-SPI interface supporting PSRAM, NOR flash, HyperRAM, and HyperFlash up to 100 MHz Flexible Memory Controller (FMC) supporting SRAM, PSRAM, NOR, NAND flash, and SDRAM with up to 16-bit data bus

736 KB SRAM 192 KB ITCM SRAM 128 KB DTCM SRAM 320 KB AXI SRAM 96KB AHB SRAM

Octo-SPI interface supporting PSRAM, NOR flash, HyperRAM, and HyperFlash up to 100 MHz

Flexible Memory Controller (FMC) supporting SRAM, PSRAM, NOR, NAND flash, and SDRAM with up to 16-bit data bus

Peripherals Up to 134x GPIOs with interrupt capability, including up to 132 5V-tolerant I/Os 3x I2C interfaces with SMBus/PMBus support 1x I3C interface 5x USART, 5x UART, and 1x LPUART 6x SPI interfaces, including 3x with full-duplex I2S support 3x CAN FD controllers 1x USB OTG Full-Speed interface 2x USB Type-C Power Delivery controllers (UCPD) 1x SD/SDIO/MMC interface up to 100 MHz 2x DMA controllers (HPDMA and GPDMA) Analog peripherals 4x 12-bit ADCs up to 5 MSPS with up to 44 channels 1x dual-channel 12-bit DAC with buffered outputs 3x dual-channel 12-bit DACs for internal use 8x analog comparators Internal voltage reference (1.8V to 2.9V) Analog and digital temperature sensors 1x digital filter for PDM microphones Timers 2x high-resolution timers (HRTIM) with up to 24 PWM outputs and 1.9 ns resolution 3x 16-bit advanced motor-control timers 4x 32-bit general-purpose timers 9x 16-bit general-purpose timers 2x 16-bit basic timers 5x 16-bit low-power timers SysTick timer and RTC Independent and window watchdogs

Up to 134x GPIOs with interrupt capability, including up to 132 5V-tolerant I/Os

6x SPI interfaces, including 3x with full-duplex I2S support

2x USB Type-C Power Delivery controllers (UCPD)

Analog peripherals 4x 12-bit ADCs up to 5 MSPS with up to 44 channels 1x dual-channel 12-bit DAC with buffered outputs 3x dual-channel 12-bit DACs for internal use 8x analog comparators Internal voltage reference (1.8V to 2.9V) Analog and digital temperature sensors 1x digital filter for PDM microphones

4x 12-bit ADCs up to 5 MSPS with up to 44 channels

1x dual-channel 12-bit DAC with buffered outputs

Timers 2x high-resolution timers (HRTIM) with up to 24 PWM outputs and 1.9 ns resolution 3x 16-bit advanced motor-control timers 4x 32-bit general-purpose timers 9x 16-bit general-purpose timers 2x 16-bit basic timers 5x 16-bit low-power timers SysTick timer and RTC Independent and window watchdogs

520 MHz STM32H7P4/STM32H7P5 Arm Cortex-M7 MCUs feature Hardware Signal Processor (HSP), optional Neural-ART NPU - CNX Software

2x high-resolution timers (HRTIM) with up to 24 PWM outputs and 1.9 ns resolution

Security Readout protection (ROP) and proprietary code readout protection (PC-ROP) Active tamper detection and secure firmware upgrade support HASH accelerator supporting MD5, SHA-1, SHA-2, and HMAC 32-bit true random number generator (TRNG), NIST SP 800-90B compliant 96-bit unique device ID

Readout protection (ROP) and proprietary code readout protection (PC-ROP)

Active tamper detection and secure firmware upgrade support

HASH accelerator supporting MD5, SHA-1, SHA-2, and HMAC

32-bit true random number generator (TRNG), NIST SP 800-90B compliant

Clocks Internal oscillators – 64 MHz HSI, 48 MHz HSI48, 4 MHz CSI, and 32 kHz LSI External oscillators – 4–50 MHz HSE and 32.768 kHz LSE 3x PLLs with fractional mode

Internal oscillators – 64 MHz HSI, 48 MHz HSI48, 4 MHz CSI, and 32 kHz LSI

External oscillators – 4–50 MHz HSE and 32.768 kHz LSE

Debugging – Serial Wire Debug (SWD), JTAG, and 4 KB embedded trace buffer

Power Supply Voltage – 1.71V to 3.6V Integrated LDO regulator or SMPS step-down converter, depending on the variant Sleep, Stop, Standby, and VBAT modes Power-on reset (POR), power-down reset (PDR), programmable voltage detector (PVD), and brown-out reset (BOR) Backup battery supply with charging support

Integrated LDO regulator or SMPS step-down converter, depending on the variant

Power-on reset (POR), power-down reset (PDR), programmable voltage detector (PVD), and brown-out reset (BOR)

Packages – ECOPACK2 compliant LQFP100 – 14 × 14 mm LQFP128 – 14 × 14 mm LQFP144 – 20 × 20 mm LQFP176 – 24 × 24 mm TFBGA100 – 8 × 8 mm UFBGA176+25 – 10 × 10 mm Exposed-pad LQFP options on selected variants

Exposed-pad LQFP options on selected variants

STM32H7P4 block diagram (an STM32H7P5 block diagram would add a Neural-ART NPU)

The main difference between the two MCU families is that the STM32H7P5 includes a Neural-ART NPU, which, according to ST, runs the company’s AI-based arc-fault circuit interrupter (AFCI) model up to 40 times faster than a software implementation on the Cortex-M7. Both MCUs also include a Hardware Signal Processor (HSP) that offloads FFT, matrix, vector, and filtering operations from the Cortex-M7, reducing CPU load in applications such as motor control, power conversion, and industrial sensing. According to ST, the HSP can execute FFT operations up to five times faster than a software implementation running on the Cortex-M7.

In terms of software support, the company provides the STM32CubeH7P package with HAL2 and low-level drivers, middleware, and example projects. You can use STM32CubeMX2 for peripheral configuration and code generation, STM32CubeIDE for development and debugging, and STM32CubeProgrammer for firmware programming. The company also offers X-CUBE-MCSDK for motor control and X-CUBE-DPOWER for digital power applications.

STM32 Nucleo 144 development board with STM32H7P5II MCU STM32H7P5I-DK Discovery kit

暂无评论,快来发表第一条评论吧!No comments yet. Be the first!

📮 需求咨询📮 Inquiry