2021 年,MacBook Pro 第一次「剪了刘海」。五年之后,苹果终于又动了它的模具,这次,MacBook 也「上岛」了。

除了显示屏升级,新款 MacBook Pro 还第一次兼容触控,背面沉寂多年的苹果 Logo 也重新亮了起来。14 英寸机型一口气轻了约 170 克,拿在手里、带出门的负担都更小。
或许人们都多少有些好奇,这些变化是怎么达成的?最近,拆解机构 iFixit 把这台新 MacBook Pro 拆了个底朝天。
从发光 Logo 背后的秘密,到重新外观的机身结构,甚至苹果一向严苛的零部件配对机制,这次拆解还真挖出了不少有意思的东西。

Make the Apple Logo Glow Again
众所周知,在经典的旧款 MacBook 上,苹果用了一个很取巧的方式让 Logo 亮起来。
由于彼时用的还是 LCD 显示屏,面板背后本身就有一整块高亮度的背光板,苹果只要在上盖对应的金属壳上掏出一个镂空的苹果轮廓,显示屏的光自然就能顺便透出来。
但在换上双层串联 OLED 之后,自发光的每个像素背后再没有现成的光源可借,苹果不得不额外塞进一套专门的照明组件。

拆开上盖后发现,这套新结构藏在显示屏背后的泡棉衬垫里,核心只是一条带有 4 颗 LED 灯珠的小灯带。

光线从这 4 颗灯珠发出,打在底部的白色反射层上铺开,再穿过一层半透明的扩散膜。在不发光的时候,它看起来跟笔者现在熟悉的 MacBook Pro 差别不大,仍旧是一颗带有镜面质感的苹果;
亮屏状态下,灯珠点亮,白色光线就会透过这层镀膜柔和地透射出来,并依据环境光调节亮度。

不过,为了看到发光 Logo 的真面目,iFixit 在拆解过程中对显示屏面板开展了不可逆的破坏。尝试分离面板时,玻璃与下方的电致发光层发生撕裂,整块原本完好的显示屏和触控层当场报废。

而在苹果官网上刚刚公布的维修手册和备件清单里也能看到,官方本身就不会去单独更换这个发光 Logo 组件——一旦发生损坏,就只能更换整套包含外壳的「表明屏总成」。

不过,官网当下暂时还没有披露这块显示屏的维修报价,但想必也不会便宜。

触屏没有「紧箍咒」
苹果在限制使用者自行维修这件事上的态度向来「有口皆碑」。
早些年,苹果对零部件和软件配对的限制严苛到近乎死板:自行换块显示屏,可能丢掉原彩表明;更换 Home 键或主板,还可能导致 Touch ID、Face ID 等生物识别能力失效。
不过,这几年苹果也确实在慢慢改变。从 2022 年开放自助维修计划,到后来兼容使用二手原装零部件,再到逐步下放维修后的软件校准权限,虽然每一步走得都堪比「挤牙膏」。
这一次,iFixit 拿两台同规格的 14 英寸样机做了一次主板对调测试,想看看苹果在这台大改款的 MacBook Pro 上,又把维修权限放宽到了什么程度。

把两块主板互换装入对方机身后,开机进入了 macOS 自带的 Repair Assistant(维修助理)。平台不仅顺利识别了电池和表明屏,Touch ID 也直接借助了验证并能正常录入新指纹。
更让人意外的是触屏本身。完全不需要单独校准,开机就能正常响应手指点按和多指滑动手势,原彩表明和亮度调节也全部完好。

这就给华强北科学家们留下了一个很有趣的想象空间:一台旧模具、原本不带触控的 MacBook,有没有可能也能借助更换配件或某种「改装」的方式用上触屏呢?
「斤斤计较」的苹果,回来了
除了显示屏与发光 Logo,这套新模具在日常使用中最容易被感知到的,实际上是减重。
14 英寸整机重量降至约 1.38kg,比老款轻了 220g;16 英寸的减重幅度更大,从原来的 2.14kg 降至 1.82kg,足足轻了 320g,相当于少带一台 iPad mini + 一个 AirPods。

除了得益于 OLED 带来的减重(削减了整整 101 克)外;但机身下半部同样减轻了 92 克。
光是底盖本身,苹果就借助内部铣削偷轻了 44 克,固定底盖的螺丝也从 8 颗缩减到了 4 颗。而电池(72.6Wh)重量几乎没有变化(276g 比较 278g,仅微减 2g),扬声器甚至为了保证声学腔体而微增了 10 克。
这次,苹果为了减重可以说是绞尽了脑汁,在整台机器的金属结构件上,把能抠掉的每一克铝材都「斤斤计较」到了极致。
不过,这次新 MacBook Pro 加上触屏,也带来了一个以前不太需要操心的难题:显示屏会晃。
苹果当然可以把转轴做得更紧,让显示屏尽量纹丝不动,但这样一来,MacBook 一直为使用者津津乐道的单手开合就没那么从容了。

苹果工业外观副总裁 Molly Anderson 此前在与爱范儿的交流中谈到了这个难题。为了让显示屏在手指点按时足够稳定,又不影响单手开盖,苹果重新外观了表明屏外壳和转轴。
对于长时间抬手使用触屏的疲劳难题,苹果人机界面外观副总裁 Steve Lemay 也告诉爱范儿,触控主要是为了让滑动浏览、双指缩放、拖拽文件这些操作更顺手。

键盘和触控板仍然是 Mac 最主要的交互方式,使用者也不需要为了触屏改变原来的使用习惯。
iFixit 最终给这台机器打出了 5/10 分的维修评分,虽然仍旧谈不上出色,但相比上一代的 4 分,好歹提高了 1 分。

虽然雷雳 USB-C 接口做成了独立小板,风扇也是独立模块,但它们全都被压在主板下方。日常哪怕只是接口老化松动、风扇积灰想清理,都必须先把整块主板从机身里完全卸下来。
至于板载的 HDMI、SDXC 读卡器,以及焊接死在主板上的统一内存和固态硬盘,仍旧没有任何自主更换或升级的余地。

从藏在显示屏背后的 4 颗 LED,到为了减重重新外观的机身结构,这次拆解让笔者看清,MacBook Pro 时隔五年的大改款,变化远比外观上看到的多元。
从开放自助维修、兼容二手原装配件,到这次互换主板后触控和 Touch ID 都能照常识别,苹果这些年放宽限制的步子虽然迈得不大,但好在方向始终是向前的。

笔者乐见一台越来越轻巧、越来越好用,也越来越好修的 MacBook Pro,更乐见一个愿意倾听使用者意见,也愿意改变自己过去坚持的苹果。
本文来源:https://www.ifanr.com/1689129
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。
In 2021, the MacBook Pro got a notch for the first time. Five years later, Apple has finally changed its design again, and this time, the MacBook has also adopted the Dynamic Island.
Beyond the upgraded display, the new MacBook Pro also supports touch input for the first time, and the Apple logo on the back, dormant for many years, has illuminated once again. The 14-inch model is about 170 grams lighter at once, making it much less burdensome to hold and carry around.
Perhaps many people are somewhat curious about how these changes were achieved. Recently, teardown organization iFixit completely dismantled this new MacBook Pro.
From the secret behind the glowing logo to the redesigned chassis structure, and even Apple's notoriously strict component pairing mechanism, this teardown has indeed uncovered quite a few interesting details.
Photo | The complete set of internal components from iFixit's teardown of the 14-inch PROLED MacBook Pro
Make the Apple Logo Glow Again
As is widely known, on the classic older MacBook models, Apple used a very clever trick to make the logo light up.
Photo | Cult of Mac
Since it still used an LCD display at the time, the panel itself had a high-brightness backlight behind it. Apple only needed to cut out a hollow apple silhouette in the metal shell of the upper lid, and the light from the display would naturally shine through.
However, after switching to a tandem OLED, there was no longer a readily available light source behind each self-illuminating pixel to borrow from, leaving Apple no choice but to additionally pack in a dedicated lighting assembly.
Illustration | Diagram of the Apple iPad Pro's tandem OLED
After opening the upper lid, it was discovered that this new structure is hidden inside the foam padding behind the display; its core is just a small light strip with 4 LED beads.
Photo | iFixit
Light emitted from these 4 LED beads spreads out by hitting the white reflective layer at the bottom, then passes through a translucent diffusion film. When not illuminated, it looks barely different from the MacBook Pro the author is currently familiar with, still featuring an apple with a mirrored finish;
In the screen-on state, when the LED beads light up, the white light is softly transmitted through this coating and adjusts its brightness according to the ambient light.
Photo | iFixit
However, in order to see the true appearance of the glowing logo, iFixit caused irreversible damage to the display panel during the teardown process. While attempting to separate the panel, the glass and the electroluminescent layer beneath it tore apart, rendering the entire originally intact display and touch layer instantly scrapped.
Photo | iFixit
Furthermore, as can be seen in the repair manual and parts list recently published on Apple's official website, the company itself does not offer to replace the glowing logo component on its own—once it is damaged, the entire "display assembly" that includes the housing must be replaced.
However, the official website has not yet disclosed the repair price for this display panel, but it is safe to assume it will not be cheap.
The Touchscreen Has No "Restraining Headband"
Apple has always been well-known for its strict stance on restricting user self-repairs.
In earlier years, Apple's restrictions on parts and software pairing were strict to the point of being nearly rigid: replacing a display yourself might cause True Tone to be lost; replacing the Home button or logic board could also lead to the failure of biometric features such as Touch ID and Face ID.
However, Apple has indeed been slowly changing over the past few years. From launching the Self Service Repair program in 2022, to later supporting the use of used original parts, and then gradually rolling out software calibration permissions for post-repair, every step has been taken at a painstakingly slow pace akin to "squeezing toothpaste".
This time, iFixit conducted a logic board swap test using two 14-inch MacBook Pro prototypes of the same specifications to see just how much Apple has expanded repair permissions on this heavily redesigned MacBook Pro.
Photo | iFixit
After swapping the two logic boards and installing them into each other's housings, the device booted into the Repair Assistant built into macOS. The system not only successfully recognized the battery and display, but Touch ID also passed verification directly and was able to normally enroll new fingerprints.
Even more surprising is the touchscreen itself. It requires absolutely no separate calibration and responds normally to finger taps and multi-finger swipe gestures right after booting, while True Tone and brightness adjustment remain fully intact.
Photo | iFixit
This leaves a very interesting space for imagination for the "Huaqiangbei scientists": is it possible for a MacBook with an older chassis that originally lacked touch capability to gain touchscreen functionality by swapping parts or through some form of "modification"?
The "gram-obsessed" Apple is back
Aside from the display and the glowing Logo, what is most easily perceived in daily use from this new chassis is actually the weight reduction.
The 14-inch model's total weight drops to approximately 1.38kg, 220g lighter than the previous generation; the 16-inch model sees an even greater weight reduction, going from the original 2.14kg down to 1.82kg—a full 320g lighter, equivalent to carrying one fewer iPad mini and one fewer pair of AirPods.
In addition to the weight reduction brought by OLED (cutting exactly 101 grams), the lower half of the body also shed 92 grams.
For the bottom cover alone, Apple shaved off 44 grams through internal milling, and the screws securing the bottom cover were reduced from 8 to 4. Meanwhile, the battery (72.6Wh) weight barely changed (276g versus 278g, a mere 2g reduction), and the speakers even gained 10 grams to ensure the acoustic chamber.
This time, Apple has truly racked its brains over weight reduction, meticulously "calculating" every single gram of aluminum that could be carved away across the entire machine's metal structural components to the extreme.
However, adding a touchscreen to this new MacBook Pro has also introduced a problem that previously wasn't much of a concern: the display wobbles.
Apple could certainly make the hinge tighter to keep the display as motionless as possible, but then the one-handed opening and closing that MacBook users have long praised would not be as effortless.
Image|iFixit
Molly Anderson, Apple's Vice President of Industrial Design, previously discussed this challenge during a conversation with iFanr. To keep the display sufficiently stable when tapped by a finger while not affecting one-handed opening, Apple redesigned the display enclosure and the hinge.
Regarding the fatigue challenge of holding one's arm up to use the touchscreen for extended periods, Steve Lemay, Apple's Vice President of Human Interface Design, also told iFanr that touch input is mainly intended to make operations such as scrolling, two-finger pinch-to-zoom, and dragging files more convenient.
Image|Apple
The keyboard and trackpad remain Mac's primary means of interaction, and users do not need to change their original usage habits for the sake of the touchscreen.
iFixit ultimately gave this machine a repairability score of 5/10; while still not particularly outstanding, it has at least improved by 1 point compared to the previous generation's 4 points.
Image|iFixit
Although the Thunderbolt USB-C ports are made into separate small boards and the fan is also a separate module, they are all positioned beneath the motherboard. In everyday scenarios, even if just a port becomes loose due to aging or the fan accumulates dust and needs cleaning, the entire motherboard must first be completely removed from the chassis.
As for the onboard HDMI, SDXC card reader, as well as the unified memory and solid-state drive soldered to the motherboard, there is still no room for independent replacement or upgrading.
Photo | iFixit
From the 4 LEDs hidden behind the display to the chassis structure redesigned for weight reduction, this teardown has made it clear to the author that the major revamp of the MacBook Pro after five years features far more diverse changes than what is seen on the surface.
From enabling self-service repair and supporting used genuine accessories, to the fact that touch controls and Touch ID still function correctly after swapping the motherboard this time, Apple's steps to relax restrictions in recent years may not have been large, but fortunately, the direction has always been forward.
Photo | iFixit
The author welcomes a MacBook Pro that is increasingly lightweight, user-friendly, and easy to repair, and is even more pleased to see an Apple that is willing to listen to user feedback and change the stances it has long insisted upon.