
本文来源:http://www.hqwc.cn/a/824664.html
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。
3.7英寸电子纸HAT驱动指南:从SPI接口到低功耗应用实战
1. 项目概述:3.7英寸电子纸HAT,一块能“记住”画面的屏幕
如果你玩过树莓派、Arduino或者STM32,肯定对各种各样的显示屏不陌生。从LCD到OLED,它们都需要持续供电才能维持画面,一旦断电,屏幕就黑了。但今天要聊的这块 3.7英寸电子纸(e-Paper)HAT ,玩法完全不同。它最大的特点就是“双稳态”:只有在刷新画面的时候才耗电,一旦画面显示完成,你就算把电源线拔了,画面也能一直留在屏幕上,像一张打印出来的纸一样。这个特性让它特别适合那些需要长时间显示固定信息,但又对功耗极其敏感的场景,比如电子价签、公交站牌、温湿度监控显示,或者一个低功耗的电子时钟。
我手头这块3.7英寸的e-Paper HAT,分辨率是400x280像素,黑白红三色显示。它通过一个HAT(Hardware Attached on Top)接口,可以直接扣在树莓派的GPIO排针上,省去了飞线的麻烦。当然,它的驱动芯片(通常是SSD1675或类似型号)也支持通过SPI接口与Arduino、Jetson Nano甚至是STM32等主流微控制器通信,通用性很强。
网上关于它的资料不少,但很多教程要么过于简略,只给个示例代码;要么就是针对特定平台,换个环境就得从头摸索。这篇手册,我想结合自己从树莓派到STM32的踩坑经历,把它从硬件原理、驱动安装、基础显示到高级应用(比如Partial Update局部刷新)的完整流程梳理清楚。无论你是想在树莓派上做个信息看板,还是想用STM32做个超低功耗的传感器显示器,这里面的细节和坑点,希望能帮你一次搞定。
2. 硬件拆解与接口原理:不仅仅是“插上就能用”
拿到这块屏幕HAT,第一眼会觉得它很简单:一块屏,一块驱动板,一排排针。但要想玩得转,尤其是想跨平台使用,必须得搞清楚板子上的每一个芯片和引脚是干什么的。
驱动板的核心是一颗e-Paper专用驱动IC,比如 SSD1675 。这颗芯片负责接收微控制器发来的图像数据,并生成复杂的时序电压波形,去驱动电子墨水胶囊里的黑白粒子移动,从而形成图像。它内部集成了RAM(帧缓存),所以我们只需要通过SPI把一整帧图片数据传给它,然后发个刷新指令,它就能自己忙活去了,此时主控MCU可以去休眠,非常省电。
除了主控IC,板上通常还有几个关键电路:
电平转换电路 :树莓派GPIO是3.3V逻辑,而有些e-Paper驱动IC的IO口可能兼容5V或需要更高电压。板载的电平转换芯片(如74HC125D)确保了信号兼容。
电源管理电路 :e-Paper刷新时需要多个电压(如VDD、VCOM等)。板载的电源芯片(可能是一颗DC-DC或LDO)负责从输入的3.3V或5V生成这些稳定电压。 这里有个坑 :有些HAT设计从树莓派的3.3V取电,但刷新时瞬时电流可能较大,导致树莓派3.3V电源被拉低,引起树莓派自身不稳定。稳妥的做法是,如果板子有独立的5V输入引脚,尽量从外部给5V供电。
温度传感器 :高级一点的驱动板上会有一颗 温度传感器 (如NTC热敏电阻或数字传感器)。这是因为电子墨水的刷新效果(对比度、残影)受温度影响很大。驱动IC可以根据温度自动调整刷新电压波形,以达到最佳显示效果。如果你的项目环境温度变化大,这个功能至关重要。
虽然它叫树莓派HAT,但引脚定义是标准的,我们可以把它用在任何有SPI接口的设备上。以下是核心引脚的功能解析:
注意 :不同厂商的板子,引脚名称可能略有差异(如CS可能叫 SCE ,DC可能叫 D/C ),但功能相同。连接前一定要找到对应的原理图或引脚图。
树莓派 :直接插在40Pin GPIO排针上,通常板子标注了对应关系。确保方向正确(USB口方向一致)。
Arduino Uno :需要杜邦线连接。例如: DIN->D11(MOSI) , CLK->D13(SCK) , CS->D10 , DC->D9 , RST->D8 , BUSY->D7 。
STM32(以STM32F103C8T6为例) :使用硬件SPI1: DIN->PA7(MOSI) , CLK->PA5(SCK) , CS->PA4(SS) ,其他 DC 、 RST 、 BUSY 接任意GPIO,如 PB0 , PB1 , PB10 。
3. 驱动与软件环境搭建:从树莓派到STM32
驱动这块屏幕,本质上是按照其时序要求,通过SPI发送一系列命令和数据。我们可以选择使用现有的库,也可以自己从头写驱动,后者对理解原理更有帮助。
对于树莓派用户,最快捷的方式是使用屏幕供应商(如Waveshare)提供的Python库。
启用SPI接口 : sudo raspi-config 依次选择 Interface Options -> SPI -> Yes 启用。重启或使用 sudo raspi-config nonint do_spi 0 命令快速启用。
依次选择 Interface Options -> SPI -> Yes 启用。重启或使用 sudo raspi-config nonint do_spi 0 命令快速启用。
安装库与依赖 : sudo apt update sudo apt install python3-pip python3-pil python3-numpy git clone https://github.com/waveshare/e-Paper.git cd e-Paper/RaspberryPi_JetsonNano/python sudo pip3 install . 安装后,在 examples 目录下就能找到针对不同尺寸屏幕的示例程序。
安装后,在 examples 目录下就能找到针对不同尺寸屏幕的示例程序。
运行测试 : cd examples sudo python3 epd_3in7_test.py 如果一切正常,屏幕会依次显示黑白红三色的测试图案。
如果一切正常,屏幕会依次显示黑白红三色的测试图案。
权限问题 :直接运行Python脚本可能因无法访问GPIO而报错。务必使用 sudo 或以root权限运行。
库版本冲突 :如果系统已安装旧版 RPi.GPIO 或 spidev ,可能导致问题。可以尝试在虚拟环境中安装。
SPI速度 :官方库可能设置了固定的SPI速度。如果屏幕出现乱码或刷新不全,可以尝试在代码中降低SPI速度(如修改 spidev 的 max_speed_hz 参数)。
Arduino生态下有像 GxEPD2 这样的优秀通用库,它支持众多型号的e-Paper屏幕。
安装库 :在Arduino IDE中,点击 项目 -> 加载库 -> 管理库... ,搜索 GxEPD2 并安装。
选择正确的驱动类 :这是最关键的一步。 GxEPD2 库为不同驱动IC和屏幕尺寸定义了不同的类。对于3.7英寸400x280的SSD1675屏幕,通常对应的类是 GxEPD2_370_GDEY037T03 (具体需根据屏幕规格书确认)。你可以在库的 src 目录下查找或参考示例。
编写基础代码 : #include
内存消耗 :全屏缓冲区的图像数据很占内存(400x280/8 = 14KB,三色则更大)。在内存较小的Arduino Uno上,使用全缓冲区可能导致内存不足。 GxEPD2 库支持“分页”写入,可以边生成边发送,不占用完整缓冲区。
BUSY 引脚处理 :库内部会自动查询 BUSY 引脚,但你必须确保该引脚连接正确且模式设置为 INPUT 。
在STM32上使用,能让你对驱动过程有最深刻的理解。我们以STM32CubeMX和HAL库为例。
CubeMX配置 : 配置一个SPI外设(如SPI1)为全双工主模式。 将 CS 、 DC 、 RST 、 BUSY 配置为GPIO输出( RST 、 CS 、 DC )和输入( BUSY )。 注意SPI的时钟极性(CPOL)和相位(CPHA)。对于SSD1675,通常模式为 CPOL=0, CPHA=0 (即模式0)。
配置一个SPI外设(如SPI1)为全双工主模式。
将 CS 、 DC 、 RST 、 BUSY 配置为GPIO输出( RST 、 CS 、 DC )和输入( BUSY )。
注意SPI的时钟极性(CPOL)和相位(CPHA)。对于SSD1675,通常模式为 CPOL=0, CPHA=0 (即模式0)。
编写底层驱动函数 : 核心是三个函数:写命令、写数据、读忙状态。 // 引脚定义 #define EPD_CS_Clr() HAL_GPIO_WritePin(EPD_CS_GPIO_Port, EPD_CS_Pin, GPIO_PIN_RESET) #define EPD_CS_Set() HAL_GPIO_WritePin(EPD_CS_GPIO_Port, EPD_CS_Pin, GPIO_PIN_SET) // 类似定义 DC, RST 的宏 // 写命令 void EPD_WriteCmd(uint8_t cmd) { EPD_DC_Clr(); // DC置低,表示命令 EPD_CS_Clr(); // 片选拉低 HAL_SPI_Transmit(&hspi1, &cmd, 1, 100); EPD_CS_Set(); } // 写数据 void EPD_WriteData(uint8_t dat) { EPD_DC_Set(); // DC置高,表示数据 EPD_CS_Clr(); HAL_SPI_Transmit(&hspi1, &dat, 1, 100); EPD_CS_Set(); } // 读忙状态 void EPD_WaitUntilIdle(void) { while(HAL_GPIO_ReadPin(EPD_BUSY_GPIO_Port, EPD_BUSY_Pin) == 1) { HAL_Delay(10); } }
实现初始化与刷新序列 : 根据屏幕数据手册,初始化过程是一系列固定的命令和数据。你需要将厂商提供的初始化代码(通常是Arduino或树莓派库里的)移植过来,用上面的 EPD_WriteCmd 和 EPD_WriteData 函数实现。 void EPD_Init(void) { EPD_Reset(); // 硬件复位 EPD_WriteCmd(0x12); // 软件复位 EPD_WaitUntilIdle(); // ... 依次发送初始化命令序列,如设置分辨率、驱动波形等 EPD_WriteCmd(0x11); // 数据输入模式 EPD_WriteData(0x03); // ... 更多设置 } 显示一帧图像,则是先发送写RAM的命令(0x24),然后连续发送整个帧缓冲区的数据(400*280/8 = 14000字节),最后发送刷新显示的命令(0x22)和0xC7,并等待 BUSY 引脚变低。
显示一帧图像,则是先发送写RAM的命令(0x24),然后连续发送整个帧缓冲区的数据(400*280/8 = 14000字节),最后发送刷新显示的命令(0x22)和0xC7,并等待 BUSY 引脚变低。
时序严格 :某些命令后需要延时 ms 级,必须严格按照数据手册操作。
数据量巨大 :通过SPI发送14000字节数据需要时间。要优化SPI时钟速度(在CubeMX中设置),并确保使用 HAL_SPI_Transmit 发送大数据时不会超时。
帧缓冲区管理 :在STM32上开辟一个14000字节的数组(全局变量)作为帧缓冲区。绘制点、线、文字、图片的操作,最终都是修改这个缓冲区里的对应位。
4. 图像处理与显示优化:让内容更“好看”
直接显示黑白像素点阵太原始了。我们通常需要显示文字、图形甚至图片。这就涉及到图像处理。
无论在哪个平台,核心都是一个一维字节数组( uint8_t buffer[400 * 280 / 8] ),它代表了屏幕的每一个像素。数组的每个 bit 对应一个像素(1为黑,0为白)。对于三色屏,通常需要两个这样的缓冲区,分别代表黑色和红色图层。
基于这个函数,你可以实现画线、画矩形、画圆等基本图形算法。
显示文字的本质是将字模(每个字对应的点阵数据)绘制到帧缓冲区。
使用现成字库 :在树莓派Python中,PIL(Pillow)库内置了字体渲染功能,可以直接将文字转为图像。在Arduino的 GxEPD2 库中,它适配了Adafruit GFX字体系统,可以直接使用 .print() 方法。
嵌入式平台取模 :在STM32等资源受限平台,需要预先将用到的汉字、字母、数字的字模提取出来,保存为常量数组。可以使用PC端的取模软件(如PCtoLCD2002)来完成。在代码中,根据字符编码找到对应的字模数据,然后一位一位地画到缓冲区。
在树莓派上,用PIL库可以轻松打开并处理图片:
然后将图片数据传递给屏幕库的显示函数。
在STM32上,则需要先将图片转换成C语言数组。同样使用取模软件,将图片转换为十六进制数组。然后编写一个函数,将这个数组数据直接拷贝到帧缓冲区的指定位置。
重要技巧 :电子纸刷新慢,且全刷有闪烁感。更新内容时,尽量只更新变化的部分。如果只是更新几个数字,可以只重绘那个区域,而不是刷新整个屏幕。这需要更精细的缓冲区管理和局部刷新命令的支持。
5. 低功耗设计与局部刷新:进阶玩家的必修课
电子纸的招牌特性是超低功耗,但要真正发挥这个优势,需要正确的使用方法。
全局刷新 :清除整个屏幕的所有旧粒子,然后绘制新图像。过程耗时较长(约2-4秒),有明显的全屏闪烁(黑白反转过程),但显示效果最干净,无残影。适用于内容完全改变的场景。
局部刷新 :只刷新屏幕上指定区域的内容。速度快(可能几百毫秒),无全局闪烁,功耗更低。但长期局部刷新会在屏幕边缘留下“鬼影”(残影),需要定期进行几次全局刷新来清除。
发送命令,将屏幕设置为局部刷新模式。
指定要刷新的矩形区域(通过设置行、列地址命令)。
只向这个区域对应的帧缓冲区部分发送数据。
发送局部刷新命令。 注意 :并非所有e-Paper屏幕都支持硬件局部刷新,需要查阅具体驱动IC(如SSD1675)的数据手册。即使支持,其命令序列也与全局刷新不同。
在两次刷新之间,系统可以进入极低功耗的睡眠模式。
树莓派 :虽然树莓派本身功耗不低,但你可以通过 gpiozero 或 RPi.GPIO 库控制一个MOSFET开关,在刷新完成后彻底切断屏幕的电源(VCC),实现零待机功耗。同时树莓派自身可以进入轻度休眠。
Arduino/STM32 :这是发挥优势的地方。在调用 display.hibernate() (对于GxEPD2)或发送深度睡眠命令后,e-Paper驱动IC自身功耗可降至微安级。此时,主控MCU(如STM32)也可以进入 Stop 或 Standby 模式,整个系统仅靠RTC维持定时,功耗可以做到10微安以下。通过RTC定时唤醒或外部中断(如按键)唤醒,再更新屏幕,可以实现用纽扣电池运行数月甚至数年。
我的踩坑记录 :曾经试图让STM32在刷新后立即进入 Stop 模式,但发现有时唤醒后屏幕通信失败。原因是 BUSY 引脚状态未妥善处理。 正确的流程 是:发送刷新命令 -> 循环查询 BUSY 引脚直到变低(刷新完成)-> 发送深度睡眠命令 -> 再将MCU置入低功耗模式。顺序错了,屏幕可能无法正确进入睡眠。
6. 项目实战:构建一个自动刷新的天气信息站
理论说再多,不如一个实际项目。我们来设计一个基于树莓派Zero W和3.7寸e-Paper的桌面天气站。
核心功能 :每30分钟从网络API获取一次天气信息(温度、湿度、天气状况、预报),生成图片,刷新到屏幕上,然后树莓派进入休眠以省电。
可选:外接5V电源适配器(为屏幕提供更稳定电源)
系统与依赖 :安装Raspberry Pi OS Lite,启用SPI,安装Python3、pip、PIL库以及 requests 库。
生成显示图像 :使用PIL库绘制背景、文字和图标。天气图标可以预先下载一套PNG素材,根据天气状况选择。 from PIL import Image, ImageDraw, ImageFont def create_weather_image(temp, humidity, desc): image = Image.new('1', (400, 280), 255) # 白色背景 draw = ImageDraw.Draw(image) font_large = ImageFont.truetype('/usr/share/fonts/truetype/dejavu/DejaVuSans-Bold.ttf', 48) draw.text((50, 50), f"{temp}°C", font=font_large, fill=0) # ... 绘制其他信息 return image
控制屏幕刷新 :集成e-Paper的Python库,将生成的图像发送到屏幕。 关键点 :为了减少残影,可以设定每刷新5次局部天气信息后,进行一次全屏的全局刷新。
自动化与省电 :使用 cron 定时任务每30分钟执行一次脚本。在脚本末尾,可以调用系统命令让树莓派进入暂停状态( sudo halt 或使用 rtcwake 进入睡眠)。但更实用的方案是让树莓派保持运行,而仅关闭屏幕电源(如果硬件支持),因为树莓派从完全关机状态唤醒需要外部干预,不够“自动”。
网络连接不稳定 :脚本中需要增加网络检查重试机制。
图片刷新有残影 :严格按照“多次局部+一次全局”的节奏,并确保全局刷新时使用正确的清屏命令(通常是先全白再全黑再显示新内容)。
功耗依然偏高 :检查是否有其他进程在运行。可以考虑使用 systemd 服务管理脚本,并禁用不需要的树莓派外设(如HDMI、蓝牙)。
这个项目综合运用了硬件驱动、网络通信、图像处理和定时任务,是一个很好的e-Paper入门到进阶的练手项目。你可以在此基础上增加更多传感器(如室内温湿度),或者改用ESP32+STM32的组合,由ESP32负责联网获取数据,通过串口发给STM32驱动屏幕,这样可以做出功耗更低的独立设备。
玩转e-Paper的关键在于耐心和理解其工作原理。它不像普通屏幕那样“实时”,每一次刷新都需要规划和等待。但正是这种特性,让它能在那些需要“静默显示”的场合大放异彩。从按照示例点亮屏幕,到自己驱动每一个像素,再到设计出低功耗的完整应用,这个过程本身,就是硬件编程最大的乐趣所在。

本文来源:http://www.hqwc.cn/a/824664.html
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。
3.7-Inch e-Paper HAT Driver Guide: From the SPI Interface to Low-Power Applications in Practice
1. Project Overview: The 3.7-Inch e-Paper HAT — A Screen That "Remembers" Its Image
If you've used a Raspberry Pi, Arduino, or STM32, you're familiar with all kinds of displays. From LCD to OLED, they all need continuous power to maintain an image; cut the power and the screen goes black. But the 3.7-inch e-Paper HAT we're talking about today works completely differently. Its defining feature is "bistability": it only consumes power while refreshing. Once the image is displayed, you can unplug the power cable and the image stays on the screen indefinitely, like a printed sheet of paper. This makes it ideal for scenarios that need to display fixed information for a long time but are extremely power-sensitive — electronic shelf labels, bus stop signs, temperature/humidity monitors, or a low-power electronic clock.
The 3.7-inch e-Paper HAT I have on hand has a resolution of 400x280 pixels with black, white, and red display. Through a HAT (Hardware Attached on Top) interface it can sit directly on a Raspberry Pi's GPIO header, saving you the trouble of jumper wires. Of course, its driver chip (usually the SSD1675 or similar) also supports communication over SPI with Arduino, Jetson Nano, and even mainstream microcontrollers like the STM32, so it's very versatile.
There's no shortage of material online, but many tutorials are either too sketchy — just a sample sketch — or tied to a specific platform, so switching environments means starting from scratch. In this guide I want to combine my own trial-and-error experience from Raspberry Pi to STM32 and lay out the complete flow: hardware principles, driver installation, basic display, and advanced applications such as Partial Update. Whether you want an information board on a Raspberry Pi or an ultra-low-power sensor display on an STM32, I hope the details and pitfalls here help you get it right in one pass.
2. Hardware Teardown and Interface Principles: More Than Just "Plug and Play"
At first glance the HAT looks simple: a display, a driver board, and a row of pins. But to really use it — especially across platforms — you need to understand what every chip and pin on the board does.
The heart of the driver board is a dedicated e-Paper driver IC such as the SSD1675. This chip receives image data from the microcontroller and generates the complex timing voltage waveforms that move the black and white particles inside the microcapsules to form an image. It integrates RAM (a frame buffer), so we only need to send a whole frame of image data over SPI and issue a refresh command; it then goes off and does its work while the host MCU can sleep — very power-efficient.
Besides the main controller IC, the board usually has several other key circuits:
Level-shifting circuit: Raspberry Pi GPIO is 3.3V logic, while some e-Paper driver ICs' I/O may be 5V-tolerant or require higher voltages. The onboard level shifter (e.g. 74HC125D) ensures signal compatibility.
Power management circuit: refresh needs multiple voltages (VDD, VCOM, etc.). The onboard power chip (perhaps a DC-DC converter or LDO) generates these stable voltages from the 3.3V or 5V input. Here's a pitfall: some HATs draw power from the Raspberry Pi's 3.3V rail, but the instantaneous current during refresh can be large, pulling the Pi's 3.3V down and destabilizing the Pi itself. The safe approach is to feed 5V externally if the board has a separate 5V input pin.
Temperature sensor: more advanced driver boards include a temperature sensor (an NTC thermistor or a digital sensor). This matters because e-Paper refresh quality (contrast, ghosting) is heavily affected by temperature. The driver IC can automatically adjust the refresh voltage waveform according to temperature for the best display result. If your project's environment sees wide temperature swings, this feature is critical.
Although it's called a Raspberry Pi HAT, the pin definitions are standard, so we can use it on any device with an SPI interface. Here's what the core pins do:
Note: pin names may differ slightly between vendors (CS might be called SCE, DC might be D/C), but the functions are identical. Before connecting, always find the matching schematic or pinout diagram.
Raspberry Pi: plugs directly onto the 40-pin GPIO header; the board usually marks the correspondence. Make sure the orientation is correct (aligned with the USB port direction).
Arduino Uno: connect with jumper wires. For example: DIN->D11(MOSI), CLK->D13(SCK), CS->D10, DC->D9, RST->D8, BUSY->D7.
STM32 (taking STM32F103C8T6 as an example): use hardware SPI1: DIN->PA7(MOSI), CLK->PA5(SCK), CS->PA4(SS), and connect DC, RST, BUSY to any GPIO such as PB0, PB1, PB10.
3. Setting Up Drivers and the Software Environment: From Raspberry Pi to STM32
Driving this screen essentially means sending a series of commands and data over SPI according to its timing requirements. You can use an existing library or write the driver from scratch — the latter is more instructive for understanding the principles.
For Raspberry Pi users, the quickest route is the Python library provided by the screen vendor (e.g. Waveshare).
Enabling SPI: sudo raspi-config, then select Interface Options -> SPI -> Yes. Reboot, or use the command sudo raspi-config nonint do_spi 0 to enable it quickly.
Select Interface Options -> SPI -> Yes in order to enable it. Reboot, or use sudo raspi-config nonint do_spi 0 for a quick enable.
Installing the library and dependencies: sudo apt update sudo apt install python3-pip python3-pil python3-numpy git clone https://github.com/waveshare/e-Paper.git cd e-Paper/RaspberryPi_JetsonNano/python sudo pip3 install . After installation, sample programs for different screen sizes can be found in the examples directory.
After installation, you'll find sample programs for different display sizes in the examples directory.
Running a test: cd examples sudo python3 epd_3in7_test.py If everything is fine, the screen will show black, white, and red test patterns in sequence.
If all goes well, the screen will display black, white, and red test patterns one after another.
Permission issues: running a Python script directly may fail because it can't access GPIO. Be sure to use sudo or run as root.
Library version conflicts: if an older RPi.GPIO or spidev is already installed, problems may occur. Try installing inside a virtual environment.
SPI speed: the official library may set a fixed SPI speed. If the display shows garbage or refreshes incompletely, try lowering the SPI speed in the code (e.g. change spidev's max_speed_hz parameter).
In the Arduino ecosystem there's an excellent general-purpose library called GxEPD2 that supports many e-Paper models.
Installing the library: in the Arduino IDE, click Sketch -> Include Library -> Manage Libraries..., search for GxEPD2 and install it.
Choosing the right driver class: this is the most critical step. GxEPD2 defines different classes for different driver ICs and screen sizes. For a 3.7-inch 400x280 SSD1675 screen, the class is usually GxEPD2_370_GDEY037T03 (confirm against your display's datasheet). You can look in the library's src directory or check the examples.
Writing basic code: #include
Memory consumption: a full-screen frame buffer is memory-hungry (400x280/8 = 14 KB, more for three colors). On a small-memory board like the Arduino Uno, a full buffer can cause out-of-memory. GxEPD2 supports "paged" writing — generate and send page by page without holding a complete buffer.
BUSY pin handling: the library polls the BUSY pin internally, but you must ensure it's wired correctly and set to INPUT mode.
Using it on STM32 gives you the deepest understanding of the driver process. We'll use STM32CubeMX and the HAL library as an example.
CubeMX configuration: Configure a SPI peripheral (e.g. SPI1) in full-duplex master mode. Configure CS, DC, RST, BUSY as GPIO outputs (RST, CS, DC) and input (BUSY). Pay attention to SPI clock polarity (CPOL) and phase (CPHA). For the SSD1675 the usual mode is CPOL=0, CPHA=0 (mode 0).
Configure a SPI peripheral (e.g. SPI1) in full-duplex master mode.
Configure CS, DC, RST, BUSY as GPIO outputs (RST, CS, DC) and input (BUSY).
Note the SPI clock polarity (CPOL) and phase (CPHA). For the SSD1675 the usual setting is CPOL=0, CPHA=0 (mode 0).
Writing the low-level driver functions: there are three core functions — write command, write data, read busy status. // pin definitions #define EPD_CS_Clr() HAL_GPIO_WritePin(EPD_CS_GPIO_Port, EPD_CS_Pin, GPIO_PIN_RESET) #define EPD_CS_Set() HAL_GPIO_WritePin(EPD_CS_GPIO_Port, EPD_CS_Pin, GPIO_PIN_SET) // similar macros for DC and RST // write command void EPD_WriteCmd(uint8_t cmd) { EPD_DC_Clr(); // DC low means command EPD_CS_Clr(); // chip select low HAL_SPI_Transmit(&hspi1, &cmd, 1, 100); EPD_CS_Set(); } // write data void EPD_WriteData(uint8_t dat) { EPD_DC_Set(); // DC high means data EPD_CS_Clr(); HAL_SPI_Transmit(&hspi1, &dat, 1, 100); EPD_CS_Set(); } // read busy status void EPD_WaitUntilIdle(void) { while(HAL_GPIO_ReadPin(EPD_BUSY_GPIO_Port, EPD_BUSY_Pin) == 1) { HAL_Delay(10); } }
Implementing the init and refresh sequence: according to the display datasheet, initialization is a fixed series of commands and data. You need to port the vendor's init code (usually from an Arduino or Raspberry Pi library) using the EPD_WriteCmd and EPD_WriteData functions above. void EPD_Init(void) { EPD_Reset(); // hardware reset EPD_WriteCmd(0x12); // software reset EPD_WaitUntilIdle(); // ... send the init command sequence in order, e.g. resolution, waveform EPD_WriteCmd(0x11); // data entry mode EPD_WriteData(0x03); // ... more settings } To display one frame, first send the write-RAM command (0x24), then stream the entire frame buffer (400*280/8 = 14000 bytes), and finally send the display-refresh command (0x22) with 0xC7 and wait for the BUSY pin to go low.
To display one frame, first send the write-RAM command (0x24), then stream the whole frame buffer (400*280/8 = 14000 bytes), and finally send the refresh-display command (0x22) plus 0xC7 and wait for BUSY to go low.
Strict timing: some commands need millisecond-level delays after them; follow the datasheet exactly.
Huge data volume: sending 14000 bytes over SPI takes time. Optimize the SPI clock speed (set in CubeMX) and make sure HAL_SPI_Transmit doesn't time out when sending large blocks.
Frame-buffer management: allocate a 14000-byte array (a global variable) on the STM32 as the frame buffer. Drawing points, lines, text, and images ultimately comes down to modifying the corresponding bits in this buffer.
4. Image Processing and Display Optimization: Making Content Look Better
Displaying raw black-and-white pixel patterns is too primitive. Usually we need text, graphics, or even images — which brings in image processing.
On any platform, the core is a one-dimensional byte array (uint8_t buffer[400 * 280 / 8]) representing every pixel of the screen. Each bit in the array corresponds to one pixel (1 = black, 0 = white). For a three-color display you typically need two such buffers, representing the black and red layers respectively.
Based on this function, you can implement basic drawing algorithms for lines, rectangles, circles, and so on.
Displaying text essentially means drawing the font bitmap (the dot-matrix data for each character) into the frame buffer.
Using ready-made fonts: in Raspberry Pi Python, PIL (Pillow) has built-in font rendering and can turn text into an image directly. In Arduino's GxEPD2 library, it adapts the Adafruit GFX font system, so you can use .print() directly.
Generating font data for embedded platforms: on resource-constrained platforms like STM32, you need to pre-extract the dot-matrix fonts for the characters you use and save them as constant arrays. Use PC-side font-conversion software (e.g. PCtoLCD2002). In code, look up the font data by character encoding and draw it into the buffer bit by bit.
On the Raspberry Pi, PIL makes it easy to open and process images:
Then pass the image data to the display library's show function.
On STM32 you first convert the image into a C array — again using conversion software to turn the image into a hex array. Then write a function that copies this array directly into the right position in the frame buffer.
Important technique: e-Paper refreshes slowly and full refresh flickers. When updating content, refresh only what changed. If you're just updating a few numbers, redraw only that region instead of refreshing the whole screen. This requires finer buffer management and support for partial-refresh commands.
5. Low-Power Design and Partial Refresh: A Must-Learn for Advanced Users
e-Paper's signature feature is ultra-low power, but really harvesting that advantage requires using it correctly.
Full refresh: clears all old particles across the whole screen, then draws the new image. It takes longer (roughly 2–4 seconds) with obvious full-screen flicker (the black/white inversion), but gives the cleanest result with no ghosting. Use it when the content changes completely.
Partial refresh: refreshes only a specified area of the screen. It's fast (perhaps a few hundred milliseconds), has no full-screen flicker, and uses less power. However, repeated partial refreshes leave "ghosting" (residual images) around the screen edges, so you need to do a few full refreshes periodically to clear it.
Send a command to put the screen into partial-refresh mode.
Specify the rectangle to refresh (by setting the row and column address commands).
Send data only for the part of the frame buffer corresponding to that area.
Send the partial-refresh command. Note: not all e-Paper screens support hardware partial refresh — check the datasheet of the specific driver IC (e.g. SSD1675). Even when supported, its command sequence differs from a full refresh.
Between two refreshes, the system can enter an ultra-low-power sleep mode.
Raspberry Pi: although the Pi itself isn't low-power, you can use gpiozero or RPi.GPIO to control a MOSFET switch that cuts the display's VCC completely after refresh, achieving zero standby power. Meanwhile the Pi itself can go into a light sleep.
Arduino/STM32: this is where the advantage really shines. After calling display.hibernate() (with GxEPD2) or sending a deep-sleep command, the e-Paper driver IC's own consumption drops to the microamp level. At this point the host MCU (e.g. an STM32) can also enter Stop or Standby mode, with the whole system kept alive only by the RTC for timing — consumption can go below 10 microamps. Wake by RTC timer or an external interrupt (e.g. a button), then update the display, and you can run for months or even years on a coin cell.
My pitfall note: I once tried to put an STM32 into Stop mode immediately after a refresh, but sometimes communication failed after wake-up. The cause was improper handling of the BUSY pin state. The correct sequence is: send refresh command -> poll BUSY until it goes low (refresh complete) -> send deep-sleep command -> then put the MCU into low-power mode. Get the order wrong and the display may not enter sleep properly.
6. Hands-On Project: Building an Auto-Refreshing Weather Information Station
No amount of theory beats a real project. Let's design a desktop weather station based on a Raspberry Pi Zero W and a 3.7-inch e-Paper display.
Core function: fetch weather information (temperature, humidity, conditions, forecast) from a web API every 30 minutes, generate an image, refresh it onto the display, then let the Pi sleep to save power.
Optional: an external 5V power adapter (to give the display a more stable supply).
System and dependencies: install Raspberry Pi OS Lite, enable SPI, install Python 3, pip, the PIL library, and the requests library.
Generating the display image: use PIL to draw the background, text, and icons. Weather icons can be pre-downloaded as a set of PNG assets chosen according to the condition. from PIL import Image, ImageDraw, ImageFont def create_weather_image(temp, humidity, desc): image = Image.new('1', (400, 280), 255) # white background draw = ImageDraw.Draw(image) font_large = ImageFont.truetype('/usr/share/fonts/truetype/dejavu/DejaVuSans-Bold.ttf', 48) draw.text((50, 50), f"{temp}°C", font=font_large, fill=0) # ... draw other information return image
Controlling the display refresh: integrate the e-Paper Python library and send the generated image to the screen. Key point: to reduce ghosting, do one full global refresh after every five partial weather-info updates.
Automation and power saving: use cron to run the script every 30 minutes. At the end of the script you can call a system command to suspend the Pi (sudo halt, or rtcwake to sleep). But a more practical approach is to leave the Pi running and just cut the display's power (if the hardware supports it), because waking the Pi from a full shutdown needs external intervention and isn't "automatic" enough.
Unstable network connection: add network-check and retry logic to the script.
Ghosting after image refresh: strictly follow the "several partial + one full" rhythm, and make sure the full refresh uses the correct clear-screen command (usually all white, then all black, then the new content).
Power still too high: check whether other processes are running. Consider managing the script as a systemd service and disabling unneeded Raspberry Pi peripherals (HDMI, Bluetooth).
This project combines hardware driving, network communication, image processing, and scheduled tasks — a great e-Paper exercise from beginner to advanced. You can add more sensors (e.g. indoor temperature and humidity), or switch to an ESP32 + STM32 combo where the ESP32 handles connectivity and sends data over UART to the STM32 driving the display, giving you an even lower-power standalone device.
The key to mastering e-Paper is patience and understanding how it works. It isn't "real-time" like a normal screen; every refresh needs planning and waiting. But it's exactly that trait that lets it shine in situations needing a "silent display." From lighting up the screen with an example, to driving every pixel yourself, to designing a complete low-power application — that process is the greatest joy of hardware programming.