
尽管机器学习近期在机器人控制方面取得了诸多进展,仍有几个问题依然顽固地难以解决:例如移动能力,或人形机器人的全身平衡。其中,灵巧性尤其成为一个特别棘手的难题,它需要软件和硬件两方面的精密复杂;能够实现有效精细动作控制的硬件往往相当昂贵。不过,[Mahdi]一直在攻克这个问题,他打造了一只18自由度的机器手,零件成本不到300美元。
虽然这只手是该项目的重点,但它实际上是一整条前臂。骨架采用3D打印,由伺服电机驱动;与人手一样,电机大多位于前臂,并通过肌腱来驱动关节。与大多数伺服驱动的机器手不同,它使用细钢丝绳而非合成纤维线缆,这就免去了打小结的需要——肌腱只需拉紧后压接固定即可。
为减少摩擦,每根肌腱都穿过一根PTFE管。凡是肌腱需要经过关节的地方,都会穿过关节的旋转中心,这样可使肌腱路径的长度在关节弯曲时保持不变。这只手的每根手指都能左右移动,并能独立弯曲两个关节。
手臂的底座也能通过伺服电机旋转,这给伺服电机的供电带来了挑战:伺服电机汲取的电流对于小型滑环来说太大,而更大的滑环又太贵。不过,由于手臂不需要连续旋转,他改用了一卷扁平带状电缆,随关节旋转而卷入或放出,并配有一个打印的电缆导槽以防止其扭结;这不仅比滑环便宜得多,而且更紧凑。
我们此前见过几款机器手采用同样的基于肌腱的方案,其中较逼真的一些用人工肌肉取代了伺服电机。有些甚至采用了3D打印的肌腱和韧带。
本文来源:https://hackaday.com/2026/11/21/building-a-robotic-hand-on-a-budget/
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。

For all the recent advances in robot control enabled by machine learning, there are still a few problems which remain stubbornly difficult: locomotion, for example, or whole-body balance for humanoids. Dexterity, in particular, has emerged as a particularly hard problem, requiring both software and hardware sophistication; hardware capable of useful fine motor movement is often quite expensive. [Mahdi]’s been working on that problem, though, with an eighteen-degree-of-freedom robot hand that costs less than $300 in parts.
Although the hand is the main point of the project, it’s really a full forearm. The skeleton is 3D printed and driven by servo motors; like a human hand, the motors are located mostly in the forearm and use tendons to actuate the joints. Unlike most servo-driven robot hands, it uses thin steel rope instead of synthetic fiber cables, which eliminates the need to tie small knots — the tendon can simply be tensioned and crimped in place.
To reduce friction, each tendon runs through a PTFE tube. Wherever a tendon would have to go past a joint, it passes through the joint’s center of rotation, which keeps the length of the tendon’s path from changing as the joint bends. Each finger on the hand can move side-to-side and flex two joints independently.
The base of the arm can also rotate on a servo motor, which made powering the servo motors a challenge: the servos draw too much current for small slip-rings, and larger slip-rings were too expensive. Since the arm didn’t need to rotate continuously, though, he instead used a coil of flat ribbon cable which winds in or our as the joint rotates, with a printed cable guide to keep it from kinking; not only is this much cheaper than a slip ring, it’s also more compact.
We’ve seen a few robot hands take the same tendon-based approach before, and the more realistic ones replace the servo motors with artificial muscles . Some have even 3D-printed tendons and ligaments .
本文来源:https://hackaday.com/2026/11/21/building-a-robotic-hand-on-a-budget/
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。